Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hi Nordic Community
I was using the nRF Connect Android App to scan the contents of the advertisements sent by my board.
My device is C7:51:E9:6E:C7:43
My question...
When using the mcumgr tool to list images on the NRF5340 development kit, the bootable field is reported as false , and the flags field is empty for the flashed image. This...
Hello Team, I'm trying to use the implement some WolfSSL extensions into my project and get errors while building it.
Preinformation:
I installed the SDK v2.7.0 using...
On our platform we have the following configuration of firmware:
Master boot record
Boot loader
Thread application (compiled separately from the boot loader)
We...
Hi,
I am trying to write a file with dummy data on my internal flash memory mx25r6435f of nrf5340. Then read back from the file and see it in putty. Here is the folder...
Hi
I have an external NOR flash chip which is powered off on startup. The idea is to power up the flash when needed to reserve power. On startup, I get the error message...
I haven't found much documentation yet regarding multiple threads in the secure partition, so I wanted to ask if this would be possible. Was planning to also test it out myself...
Hi,
We have a requirement to not exceed 63 mW of WiFi Tx power at any time for any band (2.4 or 5 GHz) . There is a statement about changing Tx power is not supported. Can...
Hi, We are currently migrating our project, originally developed with NCS version 1.8.0, to the latest NCS 2.7.0, while incorporating MCUboot for both of them. During this...
Hello,
I am encountering an issue with the nrfutil settings generate command. Each time the command is executed with the exact same parameters, the resulting settings.hex...
SoC: nrf52840
SDK: OpenConnect 2.4.4
I have been developing an ambient noise system using I2C microphone, nrf52840 and Zigbee networks for some time. The firmare reads...
Hi,
Is nRF52811 / S140 capable of simultaneously being in peripheral (connected slave) and central (connected master) mode like described in this blog post https://jimmywongiot...
I’m working with the nRF5340 and nNF Connect SDK 2.6.1. I’m encountering an issue where, after a central device (e.g. an Android phone) forgets a bonded peripheral device...
There was a previous discussion about the option to disable/enable slave latency a few years ago:
Did this ever get implemented? Specifically interested in the feature when...
SDK: 2.6.1
I needed to add a single wire support to our device recently and I did that by using two pins TX/RX shorted and UART. It works, but current consumption sky rockets...
