to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi Q&A
Recently, the Bluetooth communication protocol (nrf52833) was added to the ESB, both can communicate normally, but there is a problem when switching between the two...
Hiii,
I have added BLE from peripheral_hids_keyboard to Peripherial_Uart,and now my PC and mobile (Android) can connect with DK(nrf52833) and can regard it as a HID,but...
Hi experts,
I am in the process of upgrading the projects based on nRF52SDK to nRF connect SDK. Previously, we used to store the entire nRF52 SDK along with our custom code...
Hi all,
Currently our team is trying to implement a bluetooth mesh sensor network. We have started testing and experimenting with the mesh interface by trying to follow...
i Used a nrf52840 DK board and zephyr sdk v2.6.0. I'm start the ble advertisement and configure the gpio interrupt on sw1 in low mode flag GPIO_INT_LEVEL_INACTIVE (Low level...
Hi, I tested the TCP client AT command in nrf9160DK, I flashed the ncs v2.5.1 example of serial_lte_modem firmware on the board.
I send the command as below list:
AT#XSOCKET...
Hello
We are using nrf5340 in the new project. PCB design was made. We are currently waiting for the typesetting process to be completed. There is no Jlink on the designed...
Hello,
I am creating a new project that uses the nRF52810 as my controller, and during the development stage, I am using the PCA10040 nRF52832 development board. (I read...
I've got a custom board that puts UART_TX on P0.14 and UART_RX on P0.15, with no RTS or CTS signals. I've got a USB to UART cable that I've plugged in, and I know at the very...
Hello, I am working on an application where large amount of data are being stored onto a NOR flash. The flash is a W25Q02JV with 2Gb of storage, running little FS. My application...
During my test of the nrf5340 audio application which in the V2.6.0 SDK , Because of i need to store at least 13K data to the flash.
But when i build the project, i found...
I am using FATFS file system to store data in a .json file using sd card. When I debugged the code I got FR_INVALID_NAME issue in home.json file name. I am not very sure though...
I am using NCS SDK 2.6.1 , developing nrf52840 firmware, coding with zephyr.
I need BLE DFU function, so I add two lines to my prj.conf, following this URL: https://devzone...
Hello! I am working on nrf52840 NCS 2.6.0v I Configured the button to generate an interrupt every time it is pressed. Then, inside the interrupt handler (callback function...
