Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Hi Team,
As part of our requirement we need to fix the Advertisement to one fixed channel instead of altering between 3 channels like 37,38 and 39. If we have any sample...
Hello,
Using own BLE stack here (not SoftDevice) and having troubles with LL certification test cases with particular problem:
the tester establishes connection and...
Hi,
I would like to take current & power measurements of the nRF52833 SoC with the desired firmware file flashed to it. I am testing an application that uses the CPU temperature...
We are trying to make it so that we can permanently make one channel on the BLE module only for advertising while having the other channels flexible for other needs.
Hello, I have nrf52DK (nrf52832-PCA10040) and I wanted to test the Peripheral example in the nrf Connect SDK. I have built the project for nrf52DK_nrf52832 and then flashed...
Hi,
I am developing app using ant softdevice s212. I want nrf52832 to enter system off and stay there until interrupt from sensor occures. This interrupt is connected with...
I use nrf5340 to build esb project, I use the following code to scan rssi of different channels, but I read the value of NRF_RADIO->EVENTS_RSSIEND is 127, I hope you can tell...
Dear ,
How do I enable DCDCEN mode if I am using NCS1.8.0 SDK? Is there any Kconfig setting I need to perform to make this available?
Thanks and regards, Kevin
Hi,
Just wonder does NVS only use half of the configured size? I have configured the nvs_storage size = 0x2000 ( 8192 bytes)
So sector_count = 2 (4096 / sector)
When...
Hi Team,
We are in process of developing pairing mechanism for our peripheral device. We are considering using NFC for OOB. Here is what we think we should be doing: ...
Hello People,
I am working on a custom board and while trying ble_app_uart example code instead of the advertising name given in the code the device was showing "DFU_TARG...
Per the documentation on multi image builds , a child image folder that contains a <board>_<revision>.overlay it will be merged with BOARD.dts but I cannot do the same for...
Hi,
I'm working on a project that utilize the MAC library.
Coordinator with non-beaconed mode was previously used in the project, however the NRF 17.1.0 SDK is not compiled...
What is the threshold voltage on a nRF52840 GPIO to detect low level powered with 3.3V?
Can't find it in the datasheet. High level threshold will be 0.7*VDD right? 0.7 ...
I used to use the ncs1.2.0 SDK to develop a product for customers. Now I am porting it to the ncs1.9.0 SDK. During the adaptation process, I find that its control over SPI...
