Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
I'm using the nRF52832 in an energy harvesting application, where I need to cold-start the device and set a GPIO output high in under 50ms in order to latch the power supply...
When using AT command to send data, the baud rate is set to 9600, and the two modules are connected at different temperatures, and the data is sent through the serial debugging...
Hello everyone
The company I work for produces an nRF52840 based dongle.
We also have a bootloader which is a modified sdk example.
We need to save some important data...
I'm trying to install nrf-command-line-tools_10.17.0_amd64.deb on an up to date Debian 11, but dpkg always fails with this error:
# dpkg -i nrf-command-line-tools_10.17...
Hi there,
We appear to be having the same issue as described here and here on a nrf9160 DK. There was no clear changes to hardware at all. LED5 suddenly does not seem to...
Hi Nordic support,
I have been evaluating the nrf5340 audio DK and recently run into a build issue with the example application. I have been able to successfully build...
The following error occurred after BLE APP connects to nRF52832 device. How can debug this issue?
<error> app: ERROR 4 [NRF_ERROR_NO_MEM] at ..\..\..\..\..\..\components...
Hi.
I'm trying to include MCUboot in my application following this guide but I get this error:
I'm using version 1.8.0 of the nRF Connect SDK with a project using spm...
Hi,
I notice that the Power Profiler II (nRF-PPK2) connectors are polarized. I'd like to make special cables for my test fixture. Can you tell me the manufactures P/N for...
Hello all,
I am using the PWM and TIMER drivers on the nRF52DK board among other drivers like TWI and I get this error when trying to compile, eg. today
It can be seen...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
I use MPU6050 for my project. I wanna ask about this code caculating the value of MPU6050 . The function below caculating the value of GYRO of MPU6050.
What is the range...
Hi,
I am a newbie to the world of nRF. I am trying to develop a gateway using nRF52840dk using nRF connect SDKv2.0.0.
While I am trying to create a freestanding application...
I want to set a random address during every startup. I see a function to create a random static address."bt_addr_le_create_static()" but I'm unable to see a function that...
