Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
I followed this page in the section "Program application using nRF Connect Programmer", and tried to program my nRF5280 Dongle in Windows.
Like below, then I clicked "Write...
Dear Support Team，
I downloaded the code from github.com/.../ble_app_uart__saadc_timer_driven__scan_mode , modified the file, and burned it to 52832. After running the program...
Hi,
we need a firmware for the nRF52840 to do a function test for the EMC approval test. The test must show that the BT connection still works. It should also show if the...
Hi! I am using the following setup to run the "ble_app_uart" example:
nRF5 SDK 17.1.0
BMD 360 EVAL Board (nRF52811)
SEGGER Embedded Studio V6.32a
I selected the...
Hi ,
I am using BMD 330. Able to flash my working code using Segger.
Post flashing it gets into a loop in the following code
<sym_PAD7XREQQORPXRJMXMW2EYVS4S43S42A5D43SBA...
Hello,
Every time I restart the power(power on reset) and then use the command nrfjprog to download, the following error will appear
After I use the nrfjprog --recover...
I have read that you can save RAM with the newer implementation, so I decide to go ahead and change my code. The SDK 16 migration guide says:
< To replace app_timer v1 with...
Hi Nordic,
Is there any standard about the startup time of 32M and 32.768K crystal oscillator?
For example, if the time is larger than some ms the nRF5340 will work abnormally...
Question: Can UART ASYNC and UART INTERRUPT work together? I want to use async UART along with interrupt driven USB CDC, but I am not able to use both together.
Details...
Hi team,
I'm developing BLE keyboard and i'm interfacing keyboard with nRF52832 using Zephyr RTOS .
I have example code in SDK, I'll share the path " manthan@man:~/ncs...
Hello!
I'm trying to set up data transfer between nRF 52840 dongle and KX134 accelerometer from SparkFun. Currently I'm running the WHO_AM_I test only. The code is derived...
Hi all,
What's happening?
System reboots when "flash_erase" is called with parameters offset 0x1f000 and size 0x1000
Setup:
NCS v2.0.0
nRF52832 with 512K flash...
Hello,
Been chasing this undefined reference to `__device_dts_ord_XXX' issue around for awhile now with no clear path forward. What I am observing is extremely similar to...
Hello,
I am working on Thread client server based network. I am using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8. My development hardware is nRF52840-DK, HW Version 2...
Hi,
I am using nrf toolchain v2.0.0, and am testing the dfu-ota example over BLE by following the below link ( ) . howveer for fast boot up, i am using "
CONFIG_BOOT_VALIDATE_SLOT0_ONCE...
