Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Dear Nordic Community I am trying to get the nrfx adc driver to work with zephyr ( link ). With the help of this post , I ended up with the following code:
prj.conf -> ...
Dear Member,
I want to add ADC the main code,
but I got :
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol nrf_drv_ppi_init (referred from adc.o).
I'm using...
Hi, I am not sure whether there is I2C pins on nRF52840 Dongle board as based on the Adafruit Feather nRF52840 Express the pin is P0.11 and P0.12 as shown below: SCL 0.11...
Hello I am learning how to connect timers with gpio via PPI, i working on nrf52832dk.
So far I have connected the RTC 0 alarm channel to the LED no.3 (pin no.19) and its...
Hi, I am Shuang. I am now working on the Bluetooth direction finding function, but I have some problems, and I hope I can get your help.
I have experimented with Bluetooth...
I know Thingy:52-FW project has been marked as deprecated. https://github.com/NordicSemiconductor/Nordic-Thingy52-FW
However, I'm trying to get the development environment...
Hi，
I am using the ZBOSS SDK to develop the zigbee function, and I see that there are
TRACE_MSG(TRACE_ZCL1, ">> zb_zcl_finish_and_send_packet_common param %hd delay %d...
Hi,
based on my previous post/question here and after I managed to cconnect 5 specific address devices/peripherals from my central (DK) based on filtering (solution in the...
When I want to add LTE to my project I've done this by adding
to prj.conf. When I (pristine)build (within VScode, and when using the command line) i get the following...
Hi guys,
I am using the nRF52840 until recently - with the 2t2 library from nrfx - on a Zephyr application over the latest NCS 1.7.1
I wanted to add tag write capabilities...
Hi there
prj.conf
EXR-200-004.dts
main.c
Please refer the .dts custom board file. We took a basic file generated from nRFConnect for nRF52811, and added in some missing...
Hello,
In nRF Connect desktop application, under Bluetooth Low Energy tool v3.0.0, whenever I connect a peripheral device using this application, I see the option to update...
Hi
my application is driving a RGB LED by one wire, this is request a higher sequence , when you drive the RGB LED ,this task can not be interrupt , I am use timer3 to...
Hi all,
I'm working on a project using the nrf52832 with SDK 15.3.0. Our device is battery powered and in peripheral mode. When a central connects it sends +- 300 bytes...
