Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hi,
I have multiple devices that support Nordic DFU.
I want to update them using a Linux computer with a bluetooth dongle connected on it (and its not a Nordic Device...
Hi, There,
About the interrupt priority, can I understand it like this? "The two levels: NRF_MESH_IRQ_PRIORITY_LOWEST and NRF_MESH_IRQ_PRIORITY_THREAD have the same functions...
Hi Devzone,
I know that we can adjust "Advertising interval", "Tx power", "Tx payload" to do a power optimization when advertising. But I when I set " Advertising interval...
Hello,
I am trying to decrease the power consumption of my board (nRF52 DK) so that I can only see what's consumed in advertising beacon demo. When I measured the current...
Hi everyone,
I have a board based on thingy91. I have lis2dh and adxl372 sensors on it. They are both connected via SPI, and I've added this to my overlay file:
Also...
Hi,All:
I have finished continuous unmodulated carrier by SD fuctions as below.It is more efficent than DTM examples。But now,I don't know how to ctreat continuous modulated...
Hi,
I would to design a custom PCB with nRF52840 SOC.
I have two different power source:
1. 3V Lithium coin cell
2. 3.7V LiPO battery with charging circuitry
I will...
Hi,
I have a quetion,nRF5340 have two package, so have two diference RF circuit,as below picture,Why are the matching circuits different?
Package is QKAA aQFN94
...
Hello,
I am running ble_app_beacon on nRF52 DK. To check functionality, I try with all power sources in turn, i.e. USB cable, battery and external source. Today I realized...
Hi, I would like a more complete description of nrF52833-QIAA pins. I tried to find the specifications, but I did not find the information I wanted. I only saw some simple...
Hello,
When I use Debug, the program runs successfully. But when I try to connect with External Power Supply the program is not running, Also Reset is not wokring. Please...
Hi,
I want to measure RF conducted and receive sensitivity for nRF5340 DK, could you show the hardware connected blockgram?and please provide the RF test guideline to to...
I'm implementing a DFU controller for the secure DFU bootloader documented here . There is an edge-case I'm hitting that I'd like some clarification on.
As per the documentation...
ncs tag 1.6.1
Ubuntu 20.04
Hi
I am evaluating the Nordic nRF52840 using the Connect SDK. The nRF5 SDK has an example, ble_app_multiperipheral, showcasing a single peripheral...
