How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
nd Since i am still a newbie to nordic i wanted to know how can i break the task in smaller steps.
1)As a first step i get the values in temperature form using saadc.
...
Hi,
I am unable to find how is software interrupt generated for Softdevice.
I am able to see SD_EVT_IRQHandler()
but when this event is triggered
Sudhir Foujada...
Hi,
I am using sdk for mesh V.5 and nrf52840 dk.
I have run the serial mesh example and it worked fine.
I also modified the light switch example to send and receive...
Hi, I tried using the border router example that is provided and it works ok. I would like to install the border router software right onto a machine running ubuntu so that...
Hello! My device (peripheral) is based on nRF52840. Also, I use nRF52840 DK (central) to establish connections from the Linux side and getting of the data from the device...
Hi all,
is it possible to have the Immediate Alert client and Server at the same time? I need to have an alert from Smartphone and also to be able to send an alert to the...
Hi
In the final SLM version , please provide an option to disable and enable JTAG in software (thru AT command or by some means)
As part of security, this is needed...
Hi,
We are in the process of integrating a NRF52840 to a linux based host gateway device, which is supposed to be the gateway for another peripheral device which also run...
nrf52 dk board TWI SCANNING EXAMPLE INTERFACING WITH EXTERNAL EEPROM
Hi, this is vadivelan
I am working on a task like interfacing external EEPROM memory with nrf52dk...
Hi,
I am currently trying to a DFU where the firmware image is sent to external memory, validated and then copied to flash and executed there. I am doing this with the nrf52840...
Hi while implementing Media Transfer Protocol MTP I wanted to know how many bytes were transmitted by the host on EPOUT. I had to do a bit of research and trial/error - I...
Hi,
SDK : nRF5_SDK_15.2.0_9412b96
I want to perform pairing between mobile app and a device NRF52832 device based on the device serial number.
In other words I want...
Hello,
I come to you because I wanted to recover the GPS data in my project for that I based on the sample agps, however when I launch my project at the time of the reception...
Hello
I had integrated the DFU client stack in ble_thread_dyn_hrs_coap_srv_freertos project.
SDK : nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8
After clearing all the...
