to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hello
I am developing a firmware for nrf52832 using buttons like if I continuosly press my button for 6 seconds it will go to active mode from sleep mode and have been using...
Dear sir,
I have a light sensor connected to P0.04/AIN2 on 52820. How can i get the change of voltage?
I use the COMP, and has enabled COMP_ENABLED in sdk_config.h, compiled...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
We have a standalone application with no SDK integration. We would like to have the possibility to do OTA Updates via BLE and maybe introduce BLE support later on.
So for...
Hi,
I am trying to run IPSP example from nRF Connect SDK 1.4.2 IPSP sample (v1.4.2\zephyr\samples\bluetooth\ipsp). The "ping6 -I bt0 ff02::1" command is working fine but...
Hi, I am using the nRF52840 DevBoard with SDK 16.0 and Mesh SDK 4.1 and am building on the light_switch_client example.
I am trying to change the publication address by...
Hi,
I'm using nrf52 with s132(v17.0.0).
When I connect nrf52 with my phone, there is error like this picture.
And, the code is
When the buffer is filled, then...
Hello.
When I use NRF_SAADC_INPUT_AIN7 in SAADC, I get an error in calling nrf_drv_saadc_channel_init(). Looking at nrfx_saadc_channel_init() in nrfx_saadc.c, it seems to...
Hi,
In order to determine signal strength we parse the AT+CESQ response and regularly get +CESQ: 99,99,255,255,255,255 (the final number being the strength), but the connection...
Hi,
1、If I want to devlop zigbee with nRF52840, whether the only one sdk series is `nRF5_SDK_for_Thread_and_Zigbee_xxx` ?
2、Can BLE coexists with Zigbee in a nRF52840...
Hi,
I am using a nRF52832 module to receive some data from another nRF52832, which is sending the digitalized data to the receiver. My receiver consists of a nRF52832 module...
Hi guys,
I am trying to add some BLE OTA functions to my NRF52833 running Zigbee. I have looked into the examples in the SDK, and i can see that there is an example for...
1. Please provide the latest nRF52810-QCAA-R rohs and reach. 2. I did not find the latest nRF52810-QCAA-R rohs and reach at info. 3. The picture shown is older for the customer...
