I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hi there, I want to use CppUTest on the nRF52 to start developing my personal and not so personal projects. I am using the SDK for nRF52, with PCA10040's board. For the moment...
My nRF9160 is plugged into a Raspberry Pi and located somewhere far away from my office, where it can receive an LTE Cat-M signal. I'd like to update the LTE firmware, but...
Hi,
Recently we got Thingy91 and testing the GPS.
we have our custom nrf9160 board and GPS is working and getting coordinates in outdoor.
Im running the sample GPS application...
Hey All,
Due to my findings with this ticket ( https://devzone.nordicsemi.com/f/nordic-q-a/62255/lte-link-monitor-timing-out ), I decided to try and compile the LTE Link...
Hi All,
I am using the light switch example and have modified it a bit to send packets of data. I am able to send data from the client to group address, by setting the...
I have two beacons which are UUID filtered successfully.
I am trying to fetch major but this cannot be done just by putting an offset to p_adv_report->data.p_data. I noticed...
Hi,
nrf52 using from ble-peripheral-> ble_app_uart examle
In that ble_app_uart example receive the data from the android is ok.
But,i want transmit array type of data...
Hi.
setup is 52832, S332, SDK 15.3.0.
issue is about reset voltage.
I use CR2032 for power supply.
repeat fast put on and put off CR2032 on custom board, sometimes...
Hi All,
I am using nRF52382 and sdk 15.0. I have two SPI devices using separate pins. They work just fine separately, when I try to enable two instances I get compilation...
Hi,
As mentioned in "nRF52840 Product Specification v1.0", I have setup the high voltage mode, and use VDD as an external power of 3.3V by setting NRF_UICR -> REGOUT0 to...
I want to use 52811 as central deice, which SDK and SoftDevice should I use?
https://www.nordicsemi.com/Software-and-tools/Software/S140
It says: SoftDevice S140 is a...
Hi,
I’m looking to build the Bluetooth HCI-RPMsg sample for nRF52811.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/samples/bluetooth/hci_rpmsg/README...
Hi,
If the app keeps sending data at a certain rate, the numbers will skip and the software will stop.
I tried to see how much data I could communicate and at what speed...
Hello,
Development to blink LED only on Nordic Thingy 52 has been started after referring the following one of the post from Nordic Devzone. https://devzone.nordicsemi.com...
