Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
I am investigating using a front-end module with a nRf52840 in an 802.15.4 application. I have seen the 802.15.4 stack in the nRF5_SDK_15.3.0_59ac345 SDK. It looks like there...
We have an application for using the 802.15.4 protocol with a nRf52840 and a Front End Module. We are looking for an approach to take for integrating the FEM control into...
Hi,
I'm trying to figure out if my device is suffering from errata 172.
* How can I know if I'm using Ble_LR125Kbit or Ble_LR500Kbit? * I'm trying to use the function...
To the kind attention of Nordic support team,
I would like to do a question that is not strictly related to Nordic, but I hope your expert can kindly give me an answer,...
Hello,
I am a student who tries to make a smart IoT project using nRF9160 DK and Arducam OV5642. I am searching on the internet to where to start, but I cannot find any...
If all you need is changing PHY, Tx power and Device Name in a standard nRF52840, do you need building a new bootloader from the scratch or the is a way to edit the standard...
Hello,
I'm experimenting with the nRF SDK for Mesh v3.2.0 and a nRF52832 DK, specific with the LPN example.
I want to enable BLE DFU support so I followed the instructions...
I am programming with SDK15.0. Then I use nRFgo studio to download the merged program to the DK board. But it reported a validation failure. So I tried to download softdevice...
I am building a project that is based on the custom service example https://github.com/bjornspockeli/custom_ble_service_example but I don't like how it advertises in a way...
Hi!
I am trying to test the Immediate Alert Client application example (ble_app_ias_c) from nRF5_SDK_15.0.0 on my nRF52832 based module. I want to understand how to test...
Hello,
I'm using this example of code (nRF5_SDK_11.0.0_89a8197\examples\dfu\bootloader\pca10040\dual_bank_ble_s132\arm5_no_packs) with my custom board to perform a dfu....
I have a peripheral device based on the nRF52832, using SDK 15.3.0. It uses a bunch of the standard services, including the TX Power Service, plus a custom one. When I connect...
What would be the best example to start with if i have to send the sensor data from nrf52840 to a mobile application using SDK for mesh? I have asked this question before...
