Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi, we switched from your competition to your platform. I know you wrote somewhere that you cannot provide examples for every sensor out there. But your Nordic Dev Zone is...
I have run many tests using the light_switch demo. I have noticed that occasionally the latency is much larger. The latency jump is between sends, i.e. it will send 20 times...
I am using 3 mobiles for testing
1. One Plus 6
2. Samsung Galaxy Note 8 or Google Pixel
When I connect my hardware with #1 phone and send some data from the nRF Connect...
hello.
i am new to nrf52832
my question is when i press the button it will goes to interrupt handler then turn on the led if i press the same button led will turn off...
LTE link monitor does not work.
OS: Mac SEGGER IDE: v4.16 place: Tokyo in Japan.
I set up the environment from scratch following Get Started Assistant v0.9.2, updated...
Hi,
our installed base of sensors transmit their data in periodic BLE 4.0 beacons. I would like to develop a relay board that receives these beacons, and then retransmits...
Hi,
I want to use the nRF9160 DK for an NB-IoT application. I am located in Bavaria, Germany where there is no LTE-M coverage. I understand that I need the NB-IoT version...
To the kind attention of Nordic support team, from www.nordicsemi.com/ I downloaded all nRF24 Files.
I found very interesting the nRFgo Motherboard (nRF6310 Rev 1.4) pinout...
Hello ,
I am new to nrf52832
i am using external interrupt for led on and off
here the problem is when i press the button 1 led will turned on if i press the same button...
For Zigbee RF manufacture test, we did try nRF52840 using the sample code "radio_test" in SDK nRF5_SDK_15.3.0_59ac345,
but it seems that only the TX power information can...
Hi all,
I'm developing a buttonless DFU based application using the SDK v15.3 Following the documentation was pretty easy and I'm now able to run the app_ble_buttonless_dfu...
Hello All,
I am working on nRF51822. Use nRF51 SDk 12.3.0 version for reference. Writing program in IAR in windows.
Porting the OTA DFU to my custom APP.
use SDK 12...
Hello
I am developing a product by using nrf52840 and s340.
I know the way how to certificate ble. It is using the dtm example.
But I don't know how to certificate...
Hi
I have a question.
I am using USB CDC UART example code for my application development.
I have changed VID and PID in sdk_config.h file as per requirement.
Now...
Hi All,
I want to communicate ST25R3911B with nrf52832 controller,
It is interfaced on SPI controller.
I could not find any API related to this in SDK 15 but while searching...
