Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
Hi
I'm using pc-ble-driver-py(python2.7).
I read that python2.7 will not be maintained past 2020.
So, i want know about pc-ble-driver-py update plan.
When will the...
Hello,
We have an application based on NRF52832 which runs Nordic UART service and DFU service SDK15.2 SD132V6.0. Now, we need to add “high speed data pipe” and we are...
Hi,
I have been using nRF24 in many projects with Arduino. So far quite good experience.
Now I transfer to STM32 and have a strange problem, I cannot send with STM32 as...
Hi,
Has anyone tried connecting the grove_display to the nRF9160?
http://wiki.seeedstudio.com/Grove-LCD_RGB_Backlight/
I have tried the code below
https://github.com...
Hi All,
I'm trying to understand certificate goes where from AWS-IOT to certificate.h.
when setting a new device, I have these 4 certificates:
also the ROOT CA contains...
I have a custom Characteristic in my GATT that is sending data in Notify mode every 30ms.
In my firmware I use timer to do this with something like this :
Everything...
I'm looking to test the DPPI peripheral on the dev-kit, and to that end I though a good example would be to setup the DPPI peripheral to trigger an event when a button is...
Hi, I am new in the development. I want to interface the relay withe ble module.
But not able to do that. Please any one help me to interface the relay. Thanks in advan...
Hi,
Asset tracking example used to work for me, after reinstalling my environment I get nrf_cloud_connect failed: -111
this is the output from the LTE link monitor:
...
Hello,
I'm using the same SDK used on the Thingy:52, compiling with GCC. I'm using the Rigado BMD-350-A which uses the nrf52832.
I'd like to use P0.09 and P0.10 as GPIO...
I have three buttons connected to pins PO.07, PO.08, PO.09 on my card. I changed the pin assignment and for the first two I have no problem using them as buttons, but I can...
Hi there,
I've been trying to figure this one out for a day or so now with no luck.
I'm successfully able to build and program using Segger Embedded Studio, but I would...
Hi
I am new to nrf52840. I am trying to communicate on I2C bus with Cypress semiconductor CY8CMBR3116 capacitive touch IC. Some how I am able to connect the on I2C bus...
