I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I'm developing a battery powered BLE sensor application where I need some basic guidance on how to implement this:
The sensor action consists of a measurement process where...
Hi there!
I appreciate your work on Nordic SDKs which are getting better and better.
But sometimes SDK setup isn't as quick as it could be.
E.g. for evaluation purposes...
Hi,
I am trying to port the Thingy project (ble_app_thingy_s132_pca20020) to Segger Embedded Studio on a Mac and it proved to be not an easy task, in fact I have hit a...
Dear all, I am building a BLE thermometer based on nRF51422 chip. I need to get certify it and if any of you performed and have the tests results of the below tests, for the...
The board came pre-programmed for MBED. I don't need that, wood like to enable regular JLink. I believe the process is to get it in boot loader update mode (hold boot/reset...
Hello,
I am new in this platform. Few days ago, my boss give me a nRFgo Motherboard. He want me to write a program that nRF24le1e can read/write data from sensor via I2C...
Just verifying to be 110% sure:
The TRACEDATA1-4 pins may be used as ordinary GPIO pins when no trace-functionality is configured for the debugger? So even if a debugger...
Hi,
I have a PCA10040 connected with some wires to an external I2C device and I need to poll data from the I2C device and send it over BLE, also updating the advertisement...
Hello,
I'm looking at the different way to control / dialogue with nRF9160 module.
I know it is possible to send commands through the UART port or through the cloud, but...
Hello Support,
I have developed one device based on NRF52,it has interfaced 4 sensors.It's working fine.
Now i want add one feature is that if sometime connection lost...
Hi,
I'm doing research on Bluetooth Mesh for which I built a Mesh system for testing throughput. So currently I am sending messages at the max speed (every 25 milliseconds...
Dear Nordic,
I am trying to do the following;
nrf52840dk will be ble central
ios will be peripheral
ios will begin to advertise then nrf52840 will connect
...
We are using SDK 15.0 and Softdevice 6.0, nRF52832
The question is :(1) We migrated the example "ble_app_hrs_freertos" to "ble_app_uart_c",luckily it works ;(2) But when...
HI,
I am using NRF52832,SDK15.2
I need to work on ultra low power consumption because My project related to Health care, Fitness tracker and HOME IOT mesh network.
for...
Hi,
I'm using the TWI master example to test my application. I wanted to extend the example to write into flash (fstorage module), in a way that I can transmit data over...
