Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
I want SoftDevice of Bluetooth 4.2 for nrf52832.
I found softdevice.
15.2.0 nRF5 SDK
15.1.0 nRF5 SDK
15.0.0 nRF5 SDK
14.2.0 nRF5 SDK
etc
Which is Bluetooth 4...
i have one huge process one get positon sensor using i2c bus and another get led color also using i2c bus.
when color function is added in the process,positon sensor data...
Dear all,
I defined "DEBUG" , used UART peripheral and "printf()" in the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96. I find nRF52832 always dead in the place at...
Hello,
To determine the current network topology I hoped I could use the heartbeats to determine the RSSI and the number of hops. The RSSI of the last node is in the example...
Hi,
I found this example here for nrf51.
github.com/.../nrf51-ble-gzll-device-uart
And this is more or less what I would need for my application.
Is there a way that...
Hi All,
Scanning with a nRF52840 Dongle, Is there a way to know if one of the scanned devices is using Coded PHY modulation to advertise? And if the answer is negative,...
OS ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board CPU :(Nordic) nRF52832 / ARM Cortex -M4F 32 bit processor 28-pin Land Grid Array / 15GPIOs / SWD Soft Ver:nRF5_SDK_15...
Hi,
I am using "ble_app_uart" code and added battery service to it as custom changes.
I want to update battery level at every 3 seconds.
Code is working fine and starts...
Hi - In the examples provided, a peripheral will go to power off after completing its transactions.This means the the application does not have to "clean up" afterwards. ...
in pca10056.h, there are 4 buttons.
I want to add one new button, //#define BUTTON_5 NRF_GPIO_PIN_MAP(1,06).
However , it failed.
I debug and find the issue, #define...
i used SDK9.0.0 to implement the function that bond to cellphone.
case 1:when i set the IO_CAPABILITIES to BLE_GAP_IO_CAPS_DISPLAY_ONLY,the process of bond is ble device...
Hello,
i m using sdk15.2.0 in nrf52840.
please help for increase adv data size from 31 byte to 45 to 50 bytes..
i had tried with "BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
RTC connect through I2C and GPS connect to UART. I am getting large amount of data from gps contentiously . In the mean time i should read time from RTC . But i am getting...
