Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have an external 32MHZ crystal on my custom board.I want to configure it to 32 MHZ external crystal to operate the chip. i changed the some register configuration in software...
all works fine with iphone that mean data stored, bond 's information that has been persisted during DFU processing.everything works with iphone. but when the device that...
Dear Nordic Team,
Thanks for supporting.
Now i want support for single channel(Ch 37) advertise , please support anyone. I am using ble_app_uart example.
My SDK : SDK12...
I'm running some stress tests on a nRF52832-based product, with the following setup:
- SDK 12.0.0
- SD 3.1.0
- Compatibility modes 1 and 2 enabled.
The device exposes...
hi ,
1. How do I migrate the codec OPUS part of SR3 ? I want to use it for audio. But migration always fails. Any migration examples?
2. How effective is ANR work? Are...
I use blinky_freertos demo on nrf52832,
now I want to disable FPU,
but when I disable FPU in Keil MDK option->Target Floating Point Hardware Not Used,
there is an error...
Hi,
i am using nrf52, sdk11 and S132v2.0.0. so i want to flash the hex file using OTA so that, i have create zip file using fallowing command.
**nrfutil dfu genpkg --application...
I've been trying to set up my nRF52 DK on my mac OS.
I followed all the steps to download the SDK (15.0.0), the Command Line Tools, the ARM GCC toolchain, and the J-Link...
Hi,
I have a few doubts regarding Subnet in Bluetooth mesh:
1) If a node including in 3 subnets, how it manages to switch between multiple subnets?
2) What are the various...
Hello,
I am using nRF52832, s132_nrf5.0.0_softdevice.
I am trying to build a ble gsm gateway.
I have 3 different peripheral devices. They have some services.
On my...
Hi
I am using SDK 14.2 secure bootloader with IAR and SES build. My IAR project is working with DFU upgradation but my SES Hex file is not working
Procedure Followed...
Hi, I use s132 and SDK15 to work with nrf52832. In code I set up RTC and CC to trigger every N ticks. It works as expected and time periods counted correctly. However, when...
Hi,
I can't find the whisper mode（-30dbm TX power） on nRF52832, which is available on nRF51822.
Does is have been disabled on on nRF52832?
Regards,
Aaron
I like to build a node act as client as well as server. Is it possible to build as control model in mesh and shall i get any example for control model. Please give me any...
