Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
Is it possible to know the preamble , data format and the CRC calculation to interface a radio system ( GFSK Manchester) with NRF905 ?
Thank you
I'm wondering if the port and pin function can be used together to configure a set of pins.
For _port_dir_set, I assume it sets the whole port to the designated direction...
Hey i was using the code from developer.mbed.org/.../main.cpp
I am using this chip ( http://i.imgur.com/q8EM4uq.jpg ), it is nordic nRF51822 but i exactly do not know its...
I am using spi_master.c for spi communication with nRF51822EK.
And i had sent and recieved data packet successfully for 1st time with spi_master_send_recv(). When i sending...
Hi All,
I can compile and flash examples with my nrf51822 SDK on linux. I would like to use Code::Blocks as IDE.
Code::Blocks is transparent to run debugger. I try to...
I bought a blend micro to learn about arduino and BLE. I am a complete newbie in this field.
This is what I want to make happen,
I want to install my Blend Micro inside...
Hi All,
I am new in nrf51 development. I have a nRF51-DK kit. I would like to make development in Linux (Debian) only.
I found a lot of documents and I can compile examples...
My nRF Studio can not get nRF6130 board info,just show "Boards connected:".
But I can download fw to nRF51822 chip on the nRF6310 board.
The Application "ble_app_hrs" is...
What is the cleanest way to expose a dynamic (non-fixed amount of entries) through BLE?
One way I thought of is to create a service for a single table entry and go through...
Hi all,
I have an nRF-DK (the new one that's mbed compatible: developer.mbed.org/.../)
I have managed to completely brick it by copying the wrong file onto the BOOTLOADER...
Have tried to use an external interrupt coding.
/*------------------------------------------------------------------------------------------------------------*/
#define...
Hi, I'm a bit of a newbie to C and embedded programming. I'm using the ARM Crossworks IDE right now and trying to get the HRM_RX example working on my PCA10028 board. I've...
Hi All,
We're wirelessly giving manufacturing information to our devices, and when we're done we want to set the readback protection. We do so like this:
nrf_nvmc_write_word...
I am using SDK 7.2 and Soft Device S110 7.1. I am also using the new version of nrf51 which has 32K RAM. I am not using the DK, but a custom board, though I see the same error...
