Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
I am planning to record some information in the flash of the nRF51822. This will occupy a large circular buffer (quite a few kb), and new data (in chunks of around a dozen...
hi,
i survey the Bluetooth again , i have some issue about the Connectable mode
Connectable mode.
i see the peripheral connectable setting :
PERIPHERAL :
...
Hi Nordic,
How many connections was S120(Central) can handle simultaneously?
Does S120(Central) can received the notifications from different peripherals...
Dear all
I notice that Gzaell could only send 32 bytes a packet. But I check register PCNF1 MAXLEN can be set over than 32 bytes.
Is there any way to increase overall...
Hello,
Is there a way to set the OOB key while using the master control panel windows software?
Edit: and if not, is there a quick method to test a peripheral's OOB...
Hello!
1)There is problem with nrf_ble_uart. On sdk 4.4 work well, but sdk 5.1 the same code is not working.
What changes were made in the sdk or maybe there is a ready...
Hi I have built a custom NRF8001 board and I'm debugging a problem.
The main microcontroller works fine (atmega32u4) but the RDYN line never goes low to start the setup...
I am starting development on the nRF51422. I noticed that for the non-ANT sample code (blinky and UART), a gcc makefile and windows batch files are provided for compilation...
Hi,
Does the heart rate demo in SDK v4.4.0 work with SD v6.0.0? I'm using the QFAAC0 revision of the NRF51822. The demo works fine with SD v5.2.0. Is there anything special...
So far I haven't run across any code examples that will switch the BLE (S110) stack in and out. I'm looking to test enabling and disabling of the softdevice to see how that...
I'm reading AD-converter data usin nRF51822 SPI-Master. BLE-stack is active so I can't use
interrupts with SPI. I get data every 2 ms. Sometimes Events are delayed so long...
Hi,
We would like to implement a scenario that need two BLE devices,
One is Peripheral that able to broadcast and connectable,
another one is Central that able to scanning...
Hi,
I'm using nRF51 SDK v 5.1.0 with SoftDevice v6.0.0 on nRF51822.
I'm using the pstorage SDK module for flash operations.
I've found an issue with this module,...
Hi
In the product specification the S120 softdevice it is mentioned, that the S120 will support central and broadcaster role at the same time. This is exactly what we need...
I've cut the BLE proximity app example code back to doing nothing more than this:
int main(void)
{
uint32_t err_code;
leds_init();
for (;;)
{
power_manage...
