Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
I have used the nRF52832 on a few dozen projects, usually at 3.3V etc. On this project I have it at 1.8V, which may be related, but spec is 1.7V min, and the 1.8V supply is...
Hi Noridic team,
I am developing with nRF5340, and I added the following configuration to the prj file:
CONFIG_SPI_NOR_INIT_PRIORITY=75
However, I got the following...
Hi, I cannot compile because of the error below. Thank you in advance for any help.
I have updated the toolchain and sdk recently. Tried also with 2.6.1 and 2.7.0, the same...
I am porting the LoRa Basic Modem to the nRF52832 , using the nRF5 SDK and Segger Embedded Studio (SES) . In my application, I am using SoftDevice and implementing FOTA ....
Hi,
We recently updated our NRF Connect SDK from v2.2.0 to v2.7.0.
After porting to the SDK v2.7.0 we are not able to build the project with DFU enabled. We get below...
What is the best method to ensure the nRF9160 LTE functions on a PCB during assembly with minimal test equipment? Our thoughts were to search for available networks using...
We want use NRF5340 to do le audio application. We got the demo from your website, and find the audio demo, but the min sample rate is 32khz can be set, we want to use 8K...
I'm working with a client's existing product. It has an external MCU connected to nRF52832 via SPI.
The nRF application & SDK code are compiled inside the external MCU source...
I now want to use the 52833's board to burn the host program and then connect to other nordic slave devices. But now I put \nRF5_SDK_17.1.0\examples\ble_central\ble_app_uart_c...
Hi All,
1. The SDK used in VS code is version 2.6.1, and running the periphral_uart demo can print in rtt, but not in sid_end_ device
The official routine is used for...
Hi
First of all i am quite new to nRF SDK so if the answer to my question turns out to be trivial then I am sorry.
I am in the process of developing a Zigbee light switch...
I need to check if the Ethernet cable is connected or not, I am using the eth_click for ENC28J60. I see the driver does not allow me to see directly if the cable is connected...
Hello, How can I purchase a nRF9131 EK from Nordic Semi Sales? I was informed at the recent "Getting started with NR+ PHY" webinar that nRF9131 EK can only be purchased directly...
I would like to take Nordic's "TF-M secure peripheral partition" sample project, and modify it to take data received from the secure peripheral and send it wirelessly to another...
Hi,
I am working with the nRF5SDK , nRF Thread SDKs long time. Recently i have update segger embedded studio to V 6.30 . previously i have used v5.68
1.
for nRF 5 SDK...
