Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hello everyone,
I am planning to use the nRF9160 as the main microcontroller for my project. Alongside this, I need a Bluetooth module to transmit data to a mobile phone...
I'm using an nRF52840 as BLE peripheral with a custom service similar to NUS to send large data. The data is send in 4k chunks via BLE notifications to an Android phone. With...
In the nrf5340 Product Specification, the GPIO registers OUT, DIR, LATCH, DETECTMODE, DETECTMODE_SEC, and PIN_CNF[n] are all labeled as "Retained Registers". The definition...
I have had luck setting up signatures using MCUBOOT and sysbuild. However, I have not been able to encrypt the images. sysbuild.conf: SB_CONFIG_BOOTLOADER_MCUBOOT=y SB_CONFIG_BOOT_SIGNATURE_KEY_FILE...
I have a product that uses the nRF5 SDK that I do not plan to migrate to the nRF Connect SDK. My product uses ocrypto 3.0.8, which shipped with the latest version of the nRF5...
Hello,
I have an NRF9160DK board and a custom board running the SLM application that are exhibiting similar behaviour. Both boards work fine with the supplied iBasis SIM...
Here's a weird error, that started happening seemingly overnight: paths being parsed wrong on windows due to path separating backslashes being interpreted as escape sequences...
Hi,
I have done some searching and cannot find a direct answer to this. I have a gpio pin defined in a custom device in my board dts. I want to set this pin to high drive...
Is it posiible to use bt_disable on the nrf5340 board? for some reason it doesn't work, returns and error on this line:
if ( ! bt_dev . drv -> close ) {
return - ENOTSUP...
Hi all,
I need to modify the app.overlay dts overlay in mcuboot to be able to see the printout, among other small details. I was able to change them in the "C:/ncs/v2.5...
I'm switching from STM32 to nRF52840 and it's for a battery-operated device that only wakes up every few hours and only stays awake for about 10 seconds. With the STM32 (and...
One of our products uses the NRF51822 for Bluetooth communication.
This product is now undergoing CE certification. Is there a CE DoC (Declaration of Conformity) for the...
When creating a new board in the nRF Connect VSCode IDE, and just entering the basic items for name, if trying to use sysbuild there is a CMake error. I used name "foo" and...
I'm running Windows 11, have the kit connected with a microUSB cable and it shows up as a properly working nRF device on COM5 in device manager. I'm using v5.0.2 of nRF Connect...
Dear Nordic team,
I have developed a device using N51802QFAA, but I am doubt whether this chip will be discontinued in future. If you are going stop its production, when...
