Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
I am trying to a interrupt on when the sensor has noticed 1G movement for 150MS
Is this the correct way to configure it?
const struct device * const sensor = DEVICE_DT_GET_ANY...
I want to create a NR3540 DK application that accepts a Classic BLE audio connection, from say, a mobile phone with classic BLE (HFS profile?), and then broadcasts that audio...
Hi, I'm working on a project using Zephyr with LittleFS mounted on a QSPI flash device. However, I'm encountering an issue when trying to erase the flash area. Here are the...
Hello everyone,
I am having trouble using the bt_nus_shell.py script and a NRF52840 development board to send shell commands. I am trying to follow the instructions mentioned...
I'm trying to reflash the dongle with the "connectivity firmware". I previously used nRF Connect to do that, but with the latest version, the bootloader got somehow corrupted...
Hello everyone,
I'm currently transitioning a project from traditional BLE communication to the Nordic UART Service (NUS). The previous setup worked fine, but after replacing...
I get error about MPU error stack size while trying to run the example from ncs v2.7.0 on nrf52833dk
I was able to build correctly and I see in the log file that it gets...
nRF Connect SDK 2.3.0 on nRF52840DK
I am trying to add a fifo to my application but when trying to allocate the memory for the data item, k_malloc always returns NULL no...
Hello,
I have custom hardware running on nRF53 and there are multiple sensors connected with it for the measurement of their different entities. The hardware is battery...
Hello Experts,
On my Windows 10 PC, I have installed nRF for Desktop v5.0.2 and J-Link Pack version 7.94e got installed along with it.
Also installed Nordic command...
I use nRF52840DK and nRF21540EK to develop BLE programs, and the program uses FLASH for BLE image storage, the program works well on the DK. However, when I burned it into...
Hello,
I try to flash my bmd-345-eval board with nrf connect visual in VS code.
But the connected devices don't show mcu but show VCOM0 and RTT on nRF connect in VS code...
Hi
I have a issue, I have 4 samples nrf9160 module, all run in same firmware with FOTA feature
I found that only one module cannot start FOTA, then I try to read message...
I am getting the following build error for a Nordic nRF5340dk
c:/ncs/toolchains/ce3b5ff664/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr-eabi/12.2.0/../../.....
