Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hello,
I am working with the USB CDC ACM Sample Application from NCS V2.1.0 on nRF52840DK and have encountered an issue when attempting to replace the UART_INTERRUPT_DRIVEN...
Hello,
I am writing to seek clarification on the difference between AT%XRAI and AT%RAI. I was testing the RAI feature using the SLM application (SDK v2.7.0 and modem firmware...
trying to program an nRF51422 chip with Segger embedded studio with soft device
i get the error
"Checking project status Building ‘ble_app_uart_c_pca10028_s130’ from solution...
Hello,
I have a custom board running as a low power node, consuming around 17uA during sleep. When I have messages back and forth, the node goes back to sleep as usual....
Dear support team: Problem description: Use \v2.7.0\nrf\samples\bluetooth\mesh\light routines to download to nRF52840-DK board, after adding it with nRF Mesh app (Android...
Hello,
I have trouble again with TX Power control. This time using Softdevice Controller and NCS2.6.0.
Previous issue which was solved (this was using Zephyr Controller...
I'm working on a Proteus-III module which needs to communicate with the on board UART0. For reasons that I still don't understand, the `uart_configure` function with which...
I would like to test event related functions on nRF5340 DK. But west build failed with undefined reference to `z_impl_k_event_init'. The following are log messages of west...
Hi,
I am trying to connect 4 devices (2 nrf devices + 2 B24 custom modules). Each of them can get connected independently as single device, but as soon as I start connecting...
I'm reading the code of peripheral_hids_mouse project and I want to select some functions to fill my own code.
prj.conf has these two config:
CONFIG_BT_GATT_UUID16_POOL_SIZE...
Hi,
I followed SDK 2.7.0 Fast Pairing example and successfully downlowd to nRF52840 PCA10056 EV board, using VS Code nRF Connect Extension.
Fast Pairing Input Device example...
Hi,
I am hoping to send/receive binary data (a protocol) on the same UART that has logging/shell enabled. Is there a way to access the UART RX traffic that the shell gets...
Hi all!
I've been working on a project using the nRF Connect extension for VS Code and I've been trying to figure out which HEX file in my build/zephyr folder for my application...
Hi,
I am sending a SCAN_REQ packet from my code after receiving an Advertising packet from the NRF5340 DUT. Sometimes I receive the SCAN_RSP packet, but other times I encounter...
I am working on a project where my hardware includes an array of LEDs. I want to run an LED pattern on the array during the DFU process. I have tried to find a solution for...
