Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
How are the 28-UFBGA pin assignments translated to numbering used to specify I/O pin numbers in the code. Is this as simple as P0.0 => 0, P0.1 => 1,...? I have seen similar...
software:ncs2.5.1
chip:nrf5340
hi professor,
I want to use dtm to test blue RF. After i compile dtm example by vs code and download merge.hex by nrf connect sdk programmer...
Hello,
I am experiencing an issue where ble_nus_data_send returns a value of 0x08. I would appreciate any advice on how to resolve this error.
Symptoms: The device ...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
I used UART for communication between...
This is my log output when i connect to my ethernet
this is my prj.conf file
I am building the default AWS_IOT_MQTT SAMPLE. i dont know where i am getting the issue...
I want to implement a network of boards to be placed in a field. We have sender nodes(boards) which will collect data through saadc channels and transmit it to receiver node...
Hello,
i am developing a bootloader with softdevice112 on nrf52805.
I have setup everything and I can see bootloader and app working, just a question about memory layout...
I can't use the I2S api and I2S function in code the compiler says undefined Module , and when i checked the devicetree file there in no definition for the i2s devices
Hello,
I am programming BLE with the nRF52840-DK.
Toolchain Manager: v1.3.0
IDE: Visual Studio Code (VSCode)
SDK: ncs v2.6.0
My implementation goals are as...
With the change from nRF51 to nRF52, the data rate became a minimum of 1 Mbps.
Nordic proprietary radio mode,
nRF51 250 Kbps.
nRF52 1 Mbps,
What is the difference...
Hi everyone,
I working on a project which is a BLE peripheral with Zephyr,
I need to implement the DTM testing for production testing. I created my project base on NUS...
Whenever I respond to a question I opened myself, it generates an "Unread Notification" alert and an email.
I don't need either the website or the email to tell me that...
Hi everyone,
I trying the DTM example and run with debug, I found the software stuck at dtm clock initial. what is the problem , and how can I fixed it , thanks.
...
Hello,
I want to set the transmitting power of the advertising packet. How can I set the TX power?
I am using nRF Connect SDK 2.5.1 in Visual Studio Code.
Regards...
