Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
I have an application with the nrf52840 that was trying to port to nrf54l15 using ncs 3.2.1 but i ran into various issues. I decided to look into some samples that could help...
I am trying to program a Seeed Xiao nRF52840 Sense with a nRF5DK-52832 using the Debug out P20 connector. I am an experienced embedded systems developer (ESP32, ATTiny/AVR...
Hello,
I am developing Channel Sounding related features using nRF Connect SDK (NCS) v3.1.1 and the nRF54L15 Development Kit (DK) , based on Nordic’s official hci_uart...
I'm using custom board based on nrf9160 SoC. After migrating from SDK v3.1.1 to v3.2.1 two issues (but they are likely related) began to happen:
Battery measurements started...
Hi,
can i ask how do i send sensor readings from BME280 , SGP40 & SHT40 to nRF cloud. i has installed nRF Cloud gateway app ( Android) but it keep loading. So i am asking...
We are working with a custom nRF52840 PCB and would like guidance on the correct and supported way to build a firmware equivalent to the radio_test sample on the nRF52840...
I am working with nRF54L15 running Thread CLI . The device is successfully commissioned to a Thread network and communicates through a Border Router (BR) . SDK version V3...
I am implementing the production line frequency trimming step for the nRF7002, as per https://docs.nordicsemi.com/bundle/nan_043/page/APP/nan_043/xtalxo_freq_trimming.html...
Hello,
Is there any documentation on setting up VoIP on the nRF91x module with Zephyr?
As the nRF91x does not have a built-in VoIP app layer, I can assemble the hardware...
I have downloaded the nrf SDK v3.2.1 and i am testing its BLE sounding reflector and initiator sample code on two different xiao boards here is what i am getting at the serial...
I am using an nRF52840 DK (Version: 3.0.1). After a failed update/event, the DK is no longer recognized by my OS (Windows) via USB. LED5 blinks once when the usb is connected...
Hi:
Hardware setup: nRF52840DK interfacing with Adafruit LIS3DH (ST LIS3DH) over I2C on pins P1.14 and P1.15
Software: ncs-v3.2.1, Zephyr 4.2.99
Kconfig: I2C bus drivers...
I have a question regarding the nRF5340. I would like to capture and access the raw payload of BLE packets that fail the CRC check.
I know that with the nRF52840 (running...
I have a few doubts regarding power macros and getting the result I want. From combing through posts I have found the following: Since BT840XE has a FEM, you need to properly...
Hello Team,
Working on nrf54l15 using NCS SDK version 3.0.2 and tool chain version 3.0.2 Currently facing error while build. Following is the error
CMake Error at cmake...
