Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
Hi,
We have an application scanning 4 ADC inputs AN1, AN5, AN6 and AN7
We setup the SSADC in scanning mode:
We start sampling the ADC on a regular basis using PPI...
Hi,
I'm using a custom nrf52832 board (picture below), and I'm using nRF Connect SDK in visual code studio. I'm new to nRF so I'm a little confused about programming custom...
Dear Nordic,
We are developing nRF21540 + nRF5340 solution.
As there seems to be many versions of matching components depending on which source of information is used...
Hello,
I am currently developing a firmware where I am acting as a server with nRF52840.
The protocol of my use case is:
Client is connecting to my device (server...
NRF52: SDK v2.1.1
NRF91/SLM: SDK v2.0.0
We are seeing an issue with NRF52840 / NRF91 interaction over LPUART. When NRF91 powers up, the bootloader is not using using LPUART...
hi dev
I have a question about nrf52 dk board.
I have 2 dk board : one was written 2021.06 and the other one was written 2022.12
anyway, when I debug same file which...
We have a custom nRF9160 board which in Zephyr v1.7.1 defined in the boards\arm tree. It is a near copy of the nrf9160dk_nrf9160 folder with hardware changes and additions...
Hi Everyone,
I am using NRF52840 in my project and compiling my code using sdk 17.0.2. My application requires 7 interrupt pins to be enabled. However when I am enabling...
I have nrf9160 custom board, and I have issue with SIM module. I'm not getting 1.8 volt in "SIM_1V8" pin.
- I download the latest version from nRF Connect SDK v2.2.0 from...
Hello,
I am trying to setup a device ( Semtech LR1110 ) connected to SPI 1 peripheral on the nRF5340pdk .
I have a driver code for it. My question is this.
How can...
Hi,
Happy New Year!
I have been going over LwM2M location assistance documentation , and cannot figure out whether LwM2M library handles the response automatically, or...
I'm using Asset Tracker V2
with the Settings Enabled and tsetting up an external littlefs storage area.
I want to use the shell built in command "fs" to write stuff to...
I have two i2c modules on the same bus and I plan to have a common timer for both of these. one of these is a sensor and I only want to read the sensor values at a predefined...
Hi I am using the Zephyr code base after trying to update the ncs to 2.1.2 from 1.9.2 I notice that the function "flash_area_open" is returning a -2 error as it couldn't find...
