Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi, I use nRF52840, with SDK 15.3.0
Using UART communication, stored data should be unsigned integer 16 bit.
And the data should be calculated to float data type.
...
Hello there. I am wondering if PWM peripheral in waveform is able to generate a following sequence:
The idea, as you may see, is to generate a sequence with the same Duty...
Hello!
We have hit a wall trying to add support for a particular BLE peripheral to one of our products (which is acting as a BLE central). We support other peripherals,...
Hi Nordic Team,
We have no problem with using ble_app_hids_keyboard app,
However, in some use cases, we would like the application to run as "Just Works" to access other...
Hello everyone,
I'm currently developing a custom firmware for the Nrf52840 usb dongle ( https://www.mouser.de/new/nordic-semiconductor/nordic-nrf52840-usb-dongle ). The...
After power-up and RESET by RESET pin, power consuption of nRF9160 is ~2uA.
After wakeup by WAKEUP pin and AT#XSLEEP=2 power consuption is ~23uA.
What causes increased...
My goal is to use the atmel winc1500 wifi module with the nrf5340. - NRF5340 - NCS V1.9.0/Windows 11 - Atmel winc 1500 I started from the http_client sample (ncs\v1.9.0\zephyr...
Hello, I have soldered up a 51822 and I am trying to connect it with an EmStat pico and get measurements. I am not sure how to program the chip and get it discoverable with...
Hi,
I am using the NRF52840DK and would like to configure the GPIOs to have levels of 1,8V by using zephyr 2.4 or zephyr 3.1. By default I am getting 3 V.
Can anybody...
Hi,
I need help to use FT2232H wit OpenOCD for flashing and showing debug messages from nRF52833 Dev Kit.
Background:
I need to distribute the debug environment to...
Hi there,
We are implementing the %CONEVAL AT cmd in our project and noted that the DL-Pathloss parameter, which is supposed to be the last parameter received, is not being...
I have 3 development kits, two of them work fine with the Audio demo application and one does not: the PLAY/PAUSE button isn't doing anything.
I've probed around the switch...
I'm following this guide to add On/Off switch to the template example.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.0.2/nrf/ug_zigbee_adding_clusters.html#add...
