Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
Regarding the capacitive sensor driver with adc for nrf51 series, how am I supposed to wire my board for this to work?
https://infocenter.nordicsemi.com/index.jsp?topic...
I'm trying to follow this how to and unfortunately cannot make it past step one.
https://devzone.nordicsemi.com/guides/short-range-guides/b/software-development-kit/posts...
Hi,
I have a central that uses PM to connect to some peripherals.
If I connect to a peer (connection handle 0), and disconnect this device (e.g. by shutting it off). I...
Hi Nordic team,
We have just received our PCB prototypes with nRF52840 chip. While testing BLE functionality we found that the BLE is very weak. The connection is lost within...
Hi,
I'm trying to evaluate nrf5340_audio, but I get a build error as below.
> Executing task: nRF Connect: Build: nrf5340_audio/build (active) <
Building nrf5340_audio...
I'm trying to receive an HTTP response of approximately 100KB using the nrf9160 modem. When the response size is small recv works fine. When response is large recv returns...
GReetings,
Having a hard time using nRF Connect v3.11.1 for Desktop freshly installed on a Windows based laptop (Windows 10 Family 21H2)
J-Link V7.58b was installed simultaneously...
Good morning!
I am testing an application on Visual Studio Code + nRF Connect. I have a crash:
<err> os: Faulting instruction address (r15/pc): 0x0002c064
How can...
I have code that looks something like this:
static void some_worker(struct k_work *work) { struct state *state = CONTAINER_OF(work, struct state, some_work); k_spinlock_key_t...
My DK is connected via USB to my PC.
Uptill tommorrow it was connected and today it is saying not connected.
How to fix this ? Not sure what happened.
See below:
Have been trying to run nRF9160 sample code, including LwM2M client, and at client (latest nRF9160 firmware 1.3.2, latest SDK and Link Monitor 2.0.1) but in LTE Link Monitor...
I am unable to properly erase UICR registers on network core.
flash_erase() function that I call before flash_write() doesn't take any effect.
Example: 1. Set UICR->CUSTOMER...
I have not been able to create a stable development environment in macOS Monterey using the automatic installation process.
In order to better understand and document the...
In general, what are the steps to adding a device using GPIO pins.
My thoughts are to physically connect my peripheral to the board and configure the device tree using an...
HI,
I recently migrated my nrf52840 based devices to Thread and Zigbee SDK 4.2.0
I used to have a good power consumption around 100-150uA with zigbee enabled.
Since...
