Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Hey,
I am using an HID keyboard + keyboard toggle in my project,
When the nrf connects an iOS phone, it takes control over the phone's keyboard.
To release the kb we...
Dear ,
I am using the nRF52833-DK development board with the NCS1.7.0 SDK.
I am trying to get a PWM waveform output at 50% duty cycle with 409.6kHz frequency based on...
Hi,
I have a NRF52840 USB dongle( https://www.nordicsemi.com/Products/Development-hardware/nRF52840-Dongle); is Any possible to flash NRF52840 dongle with PTS Firmware Upgrade...
NRF52820
PAN1781 EV Board
Segger Embedded Studio 5.62
nRF5_SDK_17.1.0_ddde560
S140
Hello,
I'm currently working on an indoor positioning system and as the title...
Hi,
I compiled an application that should start at address 0x40000. However, executing an OTA DFU always places the application at 0x26000, right after the softdevice. ...
In a previous ticket on another topic this question came up. Given it was a tangent to the original topic of that thread, and I think it would be helpful to others, I decided...
Hello,
I have a battery with 4.2v max charge. Since this is outside the input range for nrf52832, I have to add a down voltage regulator. Now the question is: Should I...
Hi!
I need to modify the code of the secure and the non-secure images of my project.
I tried to follow this guide https://devzone.nordicsemi.com/guides/nrf-connect-sdk...
Hi
I have a project which is using 53832 as the master , main 52832 works with smart phone by bluetooth ,and broadcasts ebike information throght the ANT+ .
I would...
Hello everyone
I have a bunch of custom dongles from the company I work for and two of them started to behave in a strange way after I tried to erase and program them through...
Hi,
I'm currently in the evaluation phase of a project and would like to use a NRF52 chip, but I need to ensure, that I can use two independet hardware timers. I had already...
I am running a PWM pin on 15 using this DT Overlay:
pwmnmos {
compatible = "pwm-leds" ;
status = "okay" ;
pwm_nmos0: pwm_nmos_0 {
pwms = <& pwm2 15 >;
};
...
Hello,
I built my application based on your "ble_peripheral_lbs_coex" example. Board is nRF5340DK.
Mesh and BLE (NUS service) run together but I noticed that the NUS UUID...
I'm using SDK 17.1.0, softdevice 7.2.0 as a Bluetooth peripheral. I'm sending notifications to a paired iPhone. The notifications are keyboard keys, and so are time sensitive...
