How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
I am following all the steps given here: nRF Sniffer for 802.15.4 but my zigbee sniffer did not show up. When i did the steps given there for ble sniffer it showed up. steps...
Hello,
I am new to developing with Nordic products and I have a question regarding the components in the antenna matching network. I am designing around the QIAA QFN-73...
Hi,
I am trying to use the nRF915-DK with a GNSS Tracker application. Everything works fine, but, I am not able to set the nRF9151-DK properly for utilizing the board...
Hello
I'm preparing the certification RF testing software on our product 4MOD9192 using nRF7001 for wifi function.
During the certification test process, we need to...
Is it possible to add custom regions for a project to be used by the Partition Manager? I see how and where regions are defined, as shown here , but I'd like to use multiple...
I have a nrf9151dk with a nrf7002ek shield. The nrf9151dk has the DECT NR+ PHY firmware running on the modem core.
I would like to do Wi-Fi positioning with the nrf9151dk...
Hello,
I am using the nRF52833 - DK and running the USB CDC ACM example. I can transmit and receive data with the example. I noticed that when receiving data I am only able...
I am using Zephyr 3.7.0 with the Nordic-provided low level link layer (LLL) code on an nRF52840-DK. I'd like to set a breakpoint on rp_comm_rx_decode() ( https://github.com...
I want to connect two nRF54L15 development boards using I2C protocol. Is there any sample in nordic SDK v2.0.8 or v2.0.9 that I will help me to set up nRF54L15 DK as a master...
Hello,
To preface:
HW: nRF9151DK
SDK/Toolchain: nRF Connect SDK v2.9.0
I am new to Zephyr (first project)
When using a nRF91 modem, it seems that CONFIG_POSIX_API...
Hi there,
I would like to get information regarding the possibility of implementing 5.1 isochronous audio streams on the nRF5340 Audio DK development kit. According to this...
I've been using the function nrf_ble_scan_filter_set for several years with developmental hardware based on the ble_uart_c example, so I've reviewed that example thoroughly...
Hello,
I'm not able to sniff BLE using your tool
I tried to configure nrf sniffer with nrfutil.
OS: MacOS 15.1.1 (arm)
Wireshark: 4.0.17 (it seems the actual version...
Hello
Is is possible to enable MCUBoot image compression on nRF52832 ?
I tried to enable it following this blog post but I got a compilation error :
Compiler insulted...
