I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
We want to encode audio to LC3 format before we pass it to nrf5340 over USB. Because we know the processing power of nrf5340 is limited. Do you have any support for this?...
Description:
We're using GRTC on the nRF54L15 to implement RTC calendar functionality in our project. During development, we observed the following behavior:
When...
I am developing a Zigbee sensor device based on the nRF52840. I have based my firmware on the "Thingy:53: Zigbee weather station" sample. This means it is a Sleepy End Device...
We have a nrf9160 chip on a custom board with zephyr as the operation system. Modem firmware is 1.3.7. The board is battery powered, but can for development purposes also...
Hi Nordic team,
I am a test engineer at AIROHA, focusing on Zigbee and wireless communication protocol testing. Currently, I am responsible for setting up the Zigbee certification...
An error occurred while compiling the "channel_sounding_ras" process： ，A certain file is missing. I am using version 3.0.2 of ncs.Could you please tell me how to solve this...
Hi,
I am currently working on NUS sample code with one nRF5340 as central board and ISP2053 module as the Peripheral to send data with 264kbps. The peripheral is flashed...
Hi. I am currently working on a project using the nPM1300 as a pmic. For this i have a battery and an nrf5340 connected to it. Using zephyr i have even the following options...
Hi Nordic team,
I’m building a device that uses nRF9151 for cellular and an nRF7002 companion for Wi-Fi. My requirement is simple:
If a known Wi-Fi network is available...
Hi there,
I found the FW swap time in Mcuboot is too long. debugging into the code, the function, boot_move_sector_up, take ~20s, my FW is ~600k. It means the flash erase...
Hello,
Our current design does not use an external crystal for the LFCLK. As a consequence, I configured the LFCLK to use the RC oscillator. We also have power consumption...
We are using the nPM2100 with a CR2050 and CR2077 battery. There is a battery model for the CR2032 coin cell in the nrfxlib. Are there also battery models available for CR2050...
Hello,
I'm trying to add MCUBoot with sysbuild to my application (nRF Connect SDK 2.9.1). I have added sysbuild.conf (in the project's root directory), with single line...
Trying to make Thingy91's asset_tracker_v2 light sensor (BH1749) data to show up in a card on Dashboard in nrfcloud. By default asset_tracker_v2 code supporting light sensor...
