Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
My requirement is to send from Controller Device to NRF Ble Device through UART of 40Bytes at the rate of less than 1ms. Currently I am using ble_app_uart example as a reference...
Hello,
I am working on the ble_app_template example, nrf52840, SDK 17.0.2 and Segger Embedded Studio version 5.34. I have added multiple custom services to my code, however...
Hello,
as part of my project of wearable solderless modules, I've packed the nRF5340 to the same 20x20 mm form-factor - it was described earlier as part of the https://devzone...
Hi,
We have the nRF52811 in QFN48 fitted to a number of products, with the chip showing 'QAAA0 1850AA'. Does this mean that it's an early Revision 1 ? The Errata in the...
Hello,
I'm new in the Nordic sphere and I'm starting in embedded programming. I was confronted with the following problem and I will try to give as many details as possible...
Hi,
got a question about UART and maximum bytes it can receive in one burst or "packet".
Using nRF52382 and SDK16.
Recently I've been developing a new app in which UART...
Hi Nordic Team/public users,
Request your assistance for troubleshooting the NDK-nrf52840 board that was having a detection issue whereby my laptop/PC was unable to detect...
Hello, I hope you are safe and well during these times. I have created a successful prototype using the Adafruit Feather nRF52 Bluefruit and the Arduino IDE. I think I am...
Hi,
I want to update the DFU with application nRF Connect (Bluetooth) for beginning I want to try with nRF Example in example/dfu/bootloader_secure. The file secure_dfu_secure_dfu_ble_s130_pca10028_debug...
Hi,
I like to use nRFSDK in my future project, but I don't like the hectic steps to open a project when using nRFConnect SDK. I cannot open Segger IDE directly instead go...
Hi everyone,
Currently, i am working with some zigbee devices using NRF52833 and zigbee SDK 4.1. Now, i want to use BLE DFU with it to update the firmware when needed. ...
I am developing with NCS, but I found only one project "v1.4.99-dev1\nrf\samples\bluetooth\peripheral_lbs" I can add files directly through the option "Add new file to cmakelist...
I m using sdk16.0.0 nrf52-ble-app-uart-c-multilink example. I want to comminication arduino btw BT840F. I try with nrf52840 there is no problem but when i use bt840f i didn...
I'm using a library that does
#ifndef MIN
#define MIN stuff
#endif
Because I'm using segger, I have no control over compilation order, so that's getting loaded first...
