Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hello, I would like to develop a simple program that sends and receives UART communication through 2 boards.
The example used "examples\peripheral\serial\pca10056\blank...
Hi, all
I'm using nrf52832 pca10040, s132..
I want to send and receive data over Tx , Rx pin.. with my custom board, cm1106 model..
<<<<<< I've connected the two devices...
Not something which I have experienced, but rather inferred from reading the code of nRF5_SDK_17.0.2_d674dde/nRF5_SDK_17.0.2_d674dde/components/libraries/log/src/nrf_log_frontend...
HI, I'm creating an IoT system, and planning to use THREAD to communicate between devices. Each device is running on a raspberry pi but I plan to use nRF52840DKs to do all...
Hi,
I am seeing a bricked device due to the fds_init() returning FDS_ERR_NO_PAGES. After some debugging, I found that all pages are marked as FDS_PAGE_DATA (no FDS_PAGE_SWAP...
Hello everybody
I hit another issue with sd_ble_gap_disconnect.
The short story is this one. I want the peripheral to initiate a disconnect if no activity for a predefined...
Hi, I'm working on an application (Zephyr) that uses nvs storage and it's been working just great for awhile (months) without any major issues. Today I noticed that when reading...
Hi to everyone!
I am using nRF52832 driven by nRF52 DK and a sensor from Maxim Integrated. As debug output i am using the RTT viewer and as IDE Keil.
The sensor comunicate...
Hi,
Recently, I purchase another nRF52840 dongle. I realised the dongle PCB was revised to 1.2.0.
Previously, I had another dongle myself that was based on PCB ver...
Hi,
I was writing a program that uses the PPI with event from the timer and the task to one of the GPIO pins. The ideal scenario is that, whenever the timer fires, it...
I am currently experimenting the the nRF52 DK and the CSCS Peripheral example.
The provided example from the SDK creates random values for cycling speed and cadence, i.e...
I'm trying to make the sample beacon in my custom nrf52832 board, builded by Segger Embedded Studio.
The code runs fine when I'm connected to the device with the OpenOCD...
Hi,
I have an application that is mainly uart based and uses the app_scheduler, libuarte, cryptocell and pwr_manager. I want to introduce the Softdevice, and the first thing...
Hello,
I am testing the PCA10040 example project & modifying.
I was checked that the project works well in nRF52832 board.
Now, I want to download the project to nRF52810...
Hi,
I am using nRF 52 DK as a sniffer and monitoring the BLE traffic on Wireshark. The goal of this is to ensure that the communication is encrypted.
I can see that in...
