Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
HI,
we are using the nrf52840 in our new poroduct and we are running the zephyr/ncs RTOS on it.
for real time reasons I need to read from a SPI bus upon a GPIO trigger...
Hi all,
I would like to ask whether is there any details description of the matching network circuitry of NFC for NRF52840 in the datasheet.
The only information I could...
Hello,
I am following the instructions given in this ticket https://devzone.nordicsemi.com/f/nordic-q-a/57896/pdm-interface
When I call the nrfx_pdm_enable_check() the...
Hello，
We are developing wearable devices. 17 sensor terminals send data to the receiver at a frequency of 60hz per second. The data sent by 17 sensors at the same time...
Hello,
I'm interested to know whether the continuous integration and continuous deployment (CICD) is possible on nrf52840 board using Segger Embedded Studio ?
if yes,...
Hi
I currently have a nRF52833 DK which I am using as a transmitter. I also have a custom board with a nRF52811 SoC with an antenna array to act as the receiver for AoA...
Hi,
I am trying to add PWM in my application. My application uses application timer, SPI (my own written code just like CMSIS) and BLE for smartphone communication.
Everything...
I am trying to integrate buttonless DFU with FDS in ble_app_uart example from sdk 15.3.0. Merge hex was done properly which includes bootloader_settings.hex+bootloader.hex...
Hi developers and researchers,
I am working on a project in which multiple nodes are communicating with each other in p2p manner.
My goal is to implement a multiple access...
In the AWS IoT example I have been trying to add RSRP support (i.e. getting RSRP when sending my data packet).
I registered the handler/callback function in main after modem_info_init...
Is the mcuboot module compatible with RTT logging? I've setup mcuboot and my main application but cannot see any logging.
I have the following in both prj.conf & mcuboot...
Dear all,
I just writing a little piece of code (no softdevice, using sdk 17.00), that in theory toggle a led based on 2 compare (CC[0] and CC[1]).
The strange thing...
I am using SD 132 6.1.1 with a GATT server and when the client sends a Read Multiple Characteristic Values command, the nRF responds with Request Not Supported. I need to...
Hello,
I bought the Thingy 91 and tried to follow the instructions on the getting started page.
I started by downloading nRF connect - Programmer v 3.5.0. Then downloaded...
