I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
Hi, I am trying to enable TPS on an application I am staring. I have got it enabled and when I connect to the device using my phone TPS is visable, but I cannot read the value...
Hi all
I have problem with uploading app to this module. On Mqtt_simple I added
CONFIG_BOOTLOADER_MCUBOOT=y
Compile program in Segger and i got app_signed.hex. Im using...
Hello everyone,
I'm trying to make a PWM signal that fires an interrupt at the end of each PWM period. I've had the same question here:
https://devzone.nordicsemi.com...
Hi, All
In our product development, we finally found that our products need to work in long range mode to improve the communication range, and keep the connection with...
Hi,
I am a EE with a lot of background in nRF52 devices. But this is my first software venture with this device. I am familiar with the soft stacks used and have flashed...
Hi!
We develop our product on nRF52840 using S113 softdevice, version 7.0.1. From time to time, we need to erase some part of flash, so we use sd_flash_page_erase() function...
How could I rebuild the code for an NRF_CLOCK_LFCLKSRC_RC_250_PPM_250MS_CALIBRATION?
static void ble_stack_init(void)
{
uint32_t err_code;
nrf_clock_lf_cfg_t clock_lf_cfg...
Using Mesh V.4.0 and Stack 16.0.0
I have created simple message model in light_switch _client code.All I want to do is call status = simple_message_client_set(&m_clients...
Hi,
I have a simple question. How should I handle situation, when need to collect data and process them before the computed data are sended via ANT+ profile which runs on...
Hi,
I'm working with the nrf5340 and I'm trying to perform a FOTA upgrade over BLE. After initiating DFU with nrf Connect for Mobile the process crashes right after...
Hello,
I'm working on a HID BLE device and it seems to work good with iOS devices. It fails to pair with Window. I'm adding what I can see with the sniffer. Basically after...
I am read the datasheet of vl53l1x ,can anybody help on connection of vl53l1x to nrf52832 and how to use sensor vl53l1x ....any driver code for vl53l1x sensor
I want driver...
I have the following trivial program which has almost identical functionality to the connectivity/ble_connectivity/pca10040e example:
int main(void) { uint32_t err_code...
Hello,
I interfaced nRF9160 and SD card using SPI. I started with this sample: ncs/zephyr/samples/subsys/fs/fat_fs.
Now once the files from SD card are read, I want to...
Hi, I've began making a SPI module for programming a PIC16. It only transmits data, so two pins. My questions are: 1. any obvious errors? 2. does the EVENTS_ENDTX occur when...
