I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
Hi,
I am using nRF52840 and BLE coexistence (mesh and ble). I am able to connect to my board via BLE using nRFConnect for PC and a nRF52840-DK and change characteristics...
I'm trying to use DFU for the first time
I'm working my way through these instructions:
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started...
The SDK v16 package has a board file for the nRF52833 board, PCA10100, however this seems to reference GPIO pins which are not present on the device:
What should these values...
We use the nrf52832 in twi-master mode. The connected slave sometimes needs longer to respond than the default configured TWI timeout.
The timeout is defined inside the...
Is it possible to generate a zip package containing both firmware and softdevice in such way that the soft device will be updated only if the current device softdevice version...
I have some module chip connected to the nRF9160 DK providing the sensor data over I2C line. In some state transition of the module the short reset pulse needs to be generated...
Hello, I am using BLE secure bootloader example on nRF52840 with SDK 15.3 and softdevice 61.1. I can see the bootloader protects the MBR page and Bootloader space using ACL...
When I run "AT+COPS=?" WITHOUT a SIM the modem always responds properly.
When I run "AT+COPS=?" WITH a SIM the modem does not respond as expected. I get error after approx...
Hello everybody.
I have been working on nRF52840 for a time. I am trying to flash the chip with ble_app_uart_c (SDK 15.3.0). I have applied everything essential, but my...
Good morning everyone,
I am facing an apparently common problem (reported with some variations Here , Here or here ) which is driving me crazy. In the linked discussions...
I am using function "modem_info_json_object_encode" to encode modem info into JSON to send upstream.
I get the very strange format where you encode dictionary as string...
I am curious to know do we have any practical BLE based products such as Fitbit or heart rate monitor, in which there are different type of messages are sent from one end...
nrf_crypto_svc.c throws a bunch of errors during compilation. The errors have to do with SVC_REGISTER_FUNCTION. Example error message: function 'SVC_REGISTER_FUNCTION' is...
Dear ,
I just want to know about thingy 91 - pca20035 status
1. asset_tracker :nrf9160 SIP works
2. usb / usb_uart_bridge / : nrf52 ?? confusing !
and how about...
Hello Support Team,
Currently NRF52832 is being used for wearable product ,
For NFC Card Emulation Mode whether NFC Front END IC is required ?
or Can go ahead directly...
