I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hello there,
I want to run Radio Test on one nR52832 based custom board.
I have flashed the example from SDK 15.3 on the custom board using PCA10040.
I have done the...
I am trying to use nRF9160 as ble gateway for uploading data from two nRF52832. I am wondering is it possible? can I connect nRF9160 (one gatt client) to two nRF52832 (two...
Hello,
I have the following problem. I want to create a whitelist using the PM on a manually added peer.
I manually add a peer by adding its GAP address.
Then I try...
Hello!
Like several others on here, I’m trying to make a multilink nus central firmware. My Peripheral devices run the ble_app_uart example, and the central device runs...
Hello everybody !
Here I am designing a system with 3 development boards nrf52832, where a card called "central" is connected to the computer by USB and this board will...
Dear Nordic,
I'm developing an application using the NUS service en SPIM peripheral. Both of these work correctly independently. Now I'm trying to start an SPI transaction...
I'm developing IO-Link driver using UARTE peripherial.
Is it possible to get event on end of transmition with EasyDMA Tx. Event ENDTX is fired before all transmited bytes...
Segger embedded studio V4.18 appears to have a bug when it comes to printing to RTT. When I run the exact same firmware on SES V3.40, everything is printed to the debug window...
Whether I could build BLE_MESH network automatically within some BLE devices without provisioner?e.t I feel it is manual to build BLE_MESH network with the help of provis...
Hello,
for my project, I am using the module BT832A (from Fanstel) that implements the nrf52810. I am using the pin P.021 to drive a switch. The problem is that when I set...
Hello. I have a problem getting a position via GPS. My dev board is placed in a good place, but can't get a position after more than 1 hour.
I am using you new SW version...
I have been using using nRF9160 as ble gateway for uploading data from one nRF52832 and its works well. Now I need to connect more than one nRF52832 devices, has anyone tried...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hello all,
I am attempting to develop an application which utilizes a third party library for proprietary sensor calculations. This library requires the use of floating...
Hi DevZone team,
Hope you're doing great today. Just want to confirm if the nRF9160 is ready to operate in Mexico. The LTE Bands needed are B2, B4, B5 and B28. The IFETEL...
