I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hi, I have seen a few similar questions to this but the answers weren't too clear...I am trying to use both the long button push and the button push actions to generate separate...
Hello,
I have a Raytac MDBT50Q-RX USB dongle that I want to evaluate.
The dongle comes with Raytac's own test firmware.
In order to evaluate it for my purpose, I wanted...
I am very new begginer and dont know where to start about nordic nrf52832 chip. Started a week ago with downloading SDK and playing with examples in it.
I in specific need...
This is the structure.I am using bitfields here, even if i don't the problem still exists.
struct CODE_T
{ uint32_t guest_code_start_time; uint32_t guest_code_end_time;...
Hi,
Lior Neumann and Eli Biham found a vulnerabilitiy in BLE secure connections, to which CVE-2018-5383 was assigned.
Is the S132 SoftDevice affected by this vulnerabilitiy...
Hi Everyone
My requirements are as follows
1. I am running 4 tasks using free rtos in which one measures the ADC , 2nd sends the adc data over BLE and 3rd check if the...
hello
I am using sdk 15.3 example code of DFU (secure_boot loader \ pca10040_ble)
I want to debug code but i can not.I getting error like that "Error Flash Download Failed...
Hello,
I have been using this method for a while now and everything seemed to work. But for one of my device the method returns the error 0x3400. I wanted to know where...
I am trying to share ADC output to Bluetooth device. But issue is as I am getting SAADC output via SPI protocol.
Now i have added SAADC+SPI in BLE app uart example, So when...
I am trying to share ADC output to Bluetooth device. But issue is as I am getting SAADC output via SPI protocol.
Now i have added SAADC+SPI in BLE app uart example, So when...
Hi there,
I want to do scanning existing networks and for these goals, I need to enable Commissioner on Commissioner side. I use the otCommissionerStart function but when...
I am looking for an example that can work with Android 6 and higher
Current examples on Github have compilation problems probably using older gradle.
The application need...
Hi,
I'm wondering why SES 4.18 requires an entire rebuild of an application each time a project is (re)opened? I would have though it would perform an intelligent incremental...
Hi,
I am trying to modify the ble_hids_mouse example project to convert the device into a vendor defined HID device. I need to send 64 bytes of custom sensor data (which...
Hello,
I am migrating my code based on Mesh SDK V2 to V3.1.0. on nRF52840. The filter based on the uuid used in functions "prov_helper_provision_next_device" and "uuid_filter_compare...
