Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
I am using nRF51822 with SDK 10.0. I want to configure a GPIO pin which can wake up the MCU from SYSTEM OFF Mode and call its IRQ handler. Please find below configurations...
Hello,
I am using an nRF52dk with no additional hardware, in conjunction with SEGGER Embedded Studio V4.12. I started with an example from nRF5_SDK_15.3.0_59ac345 called...
Hi, I have modified the twi_scanner example of the 52840 DK to be compatible with nRFDongle.
I fully erased the dongle with Segger and passed the new hex file with SWD cable...
I used NRF connect to connect to a slave。
I want to use the central to connect to the device。
this is my code.
but the service is not found。
static void...
We are developing a platform that can have multiple configurations, with or without softdevice/ble, with or without bootloader (for upgrading), both on nrf52832 and nrf52840...
Hello,
I'm using the nRF9160DK (PCA10090 0.8.2). I was able to see the data coming from the nRF9160DK in the nrfcloud, but now I want to be able to see the data published...
Hi,
I'm working on nrf52832 NUS. When i connect to device with "nrf connect app" i can see the data coming from sensor. But few seconds later device disconnect.
When...
Hi,
To build the context: I have two peripherals, Sensor 1 and Sensor 2. Sensor 1 has been running off of a NUS service to transmit data. Sensor 2 has been running off of...
Hi all,
I make a key using nrf52832. It tranfer data to other device. I have 2 option for this. Using beacon (BLE) or Enhanced ShockBurst (ESB) . I want to optimize energy...
Hi all.
In our project we are using BLE, but at some point switch to ESB. The code below disables the SD, and sets up ESB which is then used from then on.
This all...
Hi,
I am using nRF52 DK PCA10040 to develop an application starting from the ble_app_uart example, Then I introduced PWM and SAADC from other examples, and after I verified...
I have an nRF91 DK v0.7.0 which I'm using for the first time with a Hologram.io SIM card and nothing seems to be working. Nordic sales and an FAE were here in late February...
Hello,
I need to get nrf9160 to connect to a LTE-M network. We are using a custom pcb module with nrf91 on it. I've managed to get a simple hello world, blinky and gps simulator...
Hi,
I am currently working on a project in Mesh on nRF52840 DK.
I am using the mesh v3.1.0.
I wanted to send command from mobile app to particular node in the mesh and...
