Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hello,
I am trying to fabricate a board based on the Thingy design, including the accelerometer.
I positioned the components, traces, vias and pads following some...
hello Nordic Team
I am using 2 DK
One with Light Switch Proxy Client
Another with Light Switch Proxy Switch
I am using Mobile Mesh App 1.0
Client Provisioning I...
I have been trying to use the nRF Connect app on my Apple iPhone in order to get the Current Time Service.
I bought a Arduino Primo that has an nRF52 on it.
The example...
I am working with an nRF51822 IC revision 2 chip and S110 SD 6.2.1 with Keil 5.10. My version of Keil 5.10 will not recognize the chip. I think that this is because I cannot...
Hi,
I am using nRF52832 microcontroller in project.
I use SPI interface for serial EEPROM.
I could able to see write packets are getting transmitted and verified the...
Hey, I use the Interactive mesh provisioning and configuration tutorial to setup one server and several clients which can communicate with this server.
Can you say me, how...
I have TIMER1 configured as 16-bits wide with no prescaler (62.5ns tick) and CC[2] set up for a varying value near 65535. My work is based on the Nordic blog post about synchronizing...
When I use uart to transfer data, sometimes I get error NRF_ERROR_SVC_HANDLER_MISSING in APP_UART_COMMUNICATION_ERROR when I start sending data. Sometimes this error occurs...
Hey, can I use a complex structure (for example byte array ) as a message parameter instead of one byte like it is done in http://infocenter.nordicsemi.com/index.jsp?topic...
I have a Thread network setup using nRF52840 as per the documentation below, using the Raspberry Pi image provided by Nordic. http://infocenter.nordicsemi.com/topic/com.nordic...
Hi,
In my develop environment , there have many proprietary device. One device is working on PTX mode, and the other devices is working in PRX mode.
If the PTX device...
Hi,
In the FICR (INFO.VARIANT) register on the nRF52832 soldered on my board I can read: AAB0 and in the same register on the NORDIC DK I can read AAE0.
The only different...
Hi,
as described here https://devzone.nordicsemi.com/f/nordic-q-a/37056/supervision-timeout-and-unplanned-disconnect our device has a hard current limit of 2mA.
Problem...
I have a trouble in my project.After flashing softdeivc,I flashed my application,but adversting is not work immediately, then a turn off the hardware and wait some second...
