Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Testing BLE mesh of proxy light switch example with 3 nrf52840(1 as client and 2 as servers) pdk boards with nrf mesh apk(android phone). Phone able to scan nrf 52840 light...
Dear Team,
I am using ST-Link V2 connector to program a nRF52840 board. When connected to a laptop and try to connect to the target, it says 'ST Link USB Communication...
I am currently trying to extend the range of the bluetooth mesh application. The infocentre infers that the function:
typedef struct
120 {
121 radio_tx_power_t tx_power;...
Hi,
I wonder if someone can make recommendations for types of 'smart bracelet' ('smart wristband') devices that use a BLE chip of Nordic's nRF51/nRF52 range. Can you point...
Hi,
I'm currently developing software on nrf52832. Unfortunately, I can't use the SDK for different reasons.
I'm currently looking at the RESETREAS register. If I...
I use the following code to write 32-byte to L01-module. (The wireless-communication works successfully ).
The following ( 420us+200us ), accompany only 32-byte wireless...
Hi.Is there any inbuilt ic present in nrf52840 DK board to monitor battery management ??if so, how to use that for measuring battery life?can anyone help me out plz!!
Thanks...
Good afternoon, I have a new small, but I think important, question. I did not find a concrete answer on this forum. The question concerns the correct switching of buffers...
I had try to use nRF connect to connect between nRF52840 Dongle and the bluetooth of application.
(I'm not sure the model of bluetooth of application.)
It's connected...
How many crystals/oscillators do I needfor a NRF51822 WLSCP chip?
I looked at datasheet and I'm assuming I will need a 16 Mhz crystal, a 32Mhz crystal, a 16 Mhz oscillator...
I am using IAR workbench and working with the nrf52 DK, using the S132 v.3.0 softdevice. I used the blinky example code to connect the nrf52 with my android phone over BLE...
Hello,
I got TCP Server example working on nRF52DK with Raspberry Pi.
I set everything up and can ping global addresses of DK on all interfaces (wlan0, eth0 and bt0) from...
Hello,
I am using NRF52832, SDK v15.1.0.
For advertising on single channel, I added " p_advertising->adv_params.channel_mask[4] = 03; " in ble_advertising_start() ,...
SEGGER Embedded Studio 3.12
nRF52 SDK 15.0.0
In order to generate peripheral driver library files，how to create library in project(have .c&.h file in this project).Only...
Hi,
SDK documentation says "You cannot write to UICR.BOOTLOADERADDR when using the default J-Link target driver in IAR". Some threads suggested it is only nRF51 issue, but...
