Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
By trial and error, I notice that I can only write 20 bytes to a characteristic, no matter how big I make ble_gatts_attr_t.max_len. A little googling reveals that this is...
Hi,:
I run my application program by nRF51822, about S110 V6.0 and SDK 5.2.
When the program run servial cycle functioin , it is work normail.But sometime, nRF51822 sysytem...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hello Guys,
I'm about to start my first BLE iOS project and I was wondering if there are any compatibility issues or anything that I should be aware between nRF51822 and...
im running on mac with eclipse and tried to use debugger prints, but the don't show up in the console.
Same goes for printf and uart.
Is there a flag in the makefile preventing...
Hello,
I am checking to see if it is possible to use app_twi_perform() to transmit TWI transactions that have a High Write bit. I have changed the polarity of APP_TWI_WRITE_OP...
I'm developing an embedded application using the nRF52 device. I am using GCC to build the C software and a segger flash device to program the nRF52, all using linux. I wish...
I wrote this code found in an example and it works fine:
#include "nrf_drv_config.h"
#include "nrf_drv_timer.h"
//Before I activated TIMER0, TIMER1 and TIMER2 in nrf_drv_config...
Hi,
I am using eclipse IDE and gdb to debug and flash applications onto nrf52 dk. I wish to be able to print data and messages to the eclipse console. I work on mac OSX...
I'm trying to send data over UART... started off using the examples from the SDK.
When I run the code on the dev board, I can get it working. When I load the code onto...
I want to use ESB protocol, with app_timer module to generate timer interrupts. Is it possible?
If yes could you please send some example codes for it? thanks
Per the nRF51822 product specification the NVMC ERASEPAGE operation takes up to 22.3 ms, about 730 ticks of a 32 KiHz clock. This is 365x the maximum delay between the watchdog...
For evaluating the nRF52 for a project I need to demonstrate BLE 4.2. secure pairing with NFC
I want to use two nRF52 eval boards but I need two software examples: One...
