Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
this is quote from AN36> 4.2 Set up
The nRF51822 Evaluation Kit is needed for this application example. However, it is possible to modify the
project to also work with...
Hi!
I know this might be a stupid question to you but still... I am not able to disable i.e. a timer0 cc(3) IRQ.
My way to enable it in first place:
NRF_TIMER0->INTENSET...
hi guys,
i am trying to write my own application using ble_app_template for nRF51822, but i am not at all understanding the code, did anyone developed the code for it?...
hi,
i add bond function on my project ,
now the Master Control Panel can work correctly(show the Confirm Box )
but the iOS app(on LightBlue),not show any Confirm Box for...
Is possible to put S110 in observer role (as peripheral) , waiting for a specific advertising (or waiting for an active scanning) and then switch to advertiser role (always...
Hello all,
I'd like to use NRF UART App sample code (newest iOS7 version) to send data from iOS6 to nrf51822 for "real time" data transmission. But I found that when I...
Hi,
I am having some issues transferring data from an iPhone to the nRF51822.
Actually, I write block of 16 of my data from the iPhone on a specific characteristic on...
Hello,
I have been reading the documentation about how to program a BLuetooth Low Energy application. In that document, a lot of references to an specific mannual (nRF51822S110...
I am writing one bootloader to decide two apps resided in 0x14000 to 0x40000 with nrf51822 to run. Two apps works fine when starting running itself. But when bootloader switch...
Hi experts,
i found one issue that if i continue to make the 51822 advertise(if advertise timeout, start again), sometimes the 51822 will stop in somewhere. I'm sure that...
I have just acquired the NRF51822 Evaluation Kit and going through the getting started documentation. I can't seem to fix a compiler error which is highlighted in Kiel uVision...
Hi,
I am starting my first project with nRF51822 for my thesis.
I thought its a good idea to start with evolution kit so I bought nRF51822-EK
I assume I will get everything...
Hi, I'm trying to run your ble_app_hrs on your nrf51822 chip using internal rc clock: NRF_CLOCK_LFCLKSRC_RC_250_PPM_4000MS_CALIBRATION, so I pass this to the BLE_STACK_HANDLER_INIT...
