I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hi,
as mentioned in the title, when using the official vscode extension (nRF Connect for VS Code) for debugging and stopping a debug session, the target state does not get...
Hi：
I have the following hardware structure：
FPGA < -- SPI -- > NRF5340 (TX) -- ! ( ESB ) ! -- NRF5340 (RX) < -- USB -- > PC
Due to the nature of my application, I need...
Hello!
I am trying to collect data from an nRF52832 device which works as a peripheral to another device nRF52832 which operates as both Central and Peripheral.
Description...
Hi,
I am downloading GPS Almanacs from U.S. Coast Guard Navigation Center web site to inject into the modem using nrf_modem_gnss_agps_write() . Below is current almanac...
Hello,
I need a way to decide on which Api to use for UARTE (configured as uart1) once in main(). I am not intending to switch between them nor to use them at the same...
I am currently working on a project to migrate to the nRF Connect SDK. We are using the NRF52840-CKAA-R7 package of the nRF52840. However, I have not been able to locate the...
I'm develping application on nrf52832 with nrf5SDK v17.0.
The connection interval is set to 12 to 16.And the conn_sup_timeout is set to 1000.
The condition happened frequently...
As I understand it, any applications using the modem libraries on the nRF9160 must be built in the non-secure domain. The MCUboot and TF-M needs to be in the secure domain...
Hi.
I need read the external voltage in input P030, and the battery backup voltage in P031.
If I read using only one channel, the P030 (AIN6 ) the value that show...
I want to send key strokes between two pic 16f887 microprocessors using the nRF24L01. I assume I can use ShockBurst to do the job. The master sends the key strokes and the...
Hello,
In the nrf5340_aduio application. I found it support 2 channels both of output(mic signal) and input(audio signal) on the USB device.
But i want to know if it can...
Hi,
I am debugging an application whth MPSL enabled and occasionally get this error:
E: SoftDevice Controller ASSERT: 48, 190
E: ***** HARD FAULT ***** E: Fault escalation...
Dear Nordic team,
I'm evaluating nRF5340 Audio DK for the use-case of broadcasting multiple streams.
Until now I've succeeded in broadcasting 4 streams (LC4 bitrate...
I download urfutil and install the nrf5sdk-tools in the Dockerfile
When running the image locally all is well, the installed commands are found.
But when it is running...
After interfacing my STM32 with the nRF9160-DK board and completing the programming, I now need to flash the board with the firmware update file, application file, and our...
