Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello,
I recently upgraded the MDK from an "inherited" much older version in my project to MDK version 8.63.1 for GCC. There is now a file called startup_nrf_common.c that...
I used a script to write the Gateway and Headset to the nRF5340 Audio DK board.
I used VSCODE to write the Gateway source and Headset source to the RAYTAC board.
I tried...
We have a problem where a display running on 5V with an UART on 3.3V will self-bias through the UART TX pin when the 5V supply is switched on.
How do you make zephyr not...
Hi,
We are using nRF5340 DK and the nRF Connect SDK Version 2.6.1.
We are developing a mesh network. Our requirement is the one device can connect to three other devices...
Hello.
What is correct way to use AT%MDMEV commands(searh status) to establish connection after long PSM/sleep time (168h). Our devices are used to track wild animals so...
Hello,
I'm encountering persistent address conflict issues within my Nordic project.
Occasionally, when a device joins the network, I observe address conflict errors....
Hello,
I am trying to send an array which has 2048 bytes via UART. But, when I add a some delay to repeat the the UART transfer, the code gets stuck on the HardFault. I...
Hi Community,
I report this issue in github, it seems nobody reply me, so I ask here again.
lesson 8 exercise 3 solution build failed · Issue #9 · NordicDeveloperAcademy...
Hi,
in our application we use SDCard and USB stack with the following configuration:
The communication with the nRF5340 is done by using a Linux Embedded systems. When...
I think that the source of the nRF5340 Audio DK sample board is designed so that LED1 lights up when a connection is established with CIS.
We are thinking of connecting...
Hello,
I am using the ADC on my custom board, based on nRF9160.
I am getting correct results when measuring a known voltage. However, I noticed that the execution is very...
At the company I work for we are developing a keyboard with mouse capabilities via USB and BLE using the NRF5 17.1.0 SDK. We create the USB HID with the following SDK macro...
When using the nRF9160-DK, I flash the board with Asset Tracker V2 as provided by the instructions for the board here .
The board and SIM card are registered and the board...
Hi,
I am using custom board (nRF9160) and zephyr V2.6 and I would like to make sure that I understand the ADC settings correctly in the device tree:
channel @ 1 {
...
Hi there,
I have just tried to migrate to a new M2-based mac book pro and everything went OK (i am able to build and run my sw on the target) except that I don't have any...
