How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hello,
I measured the DC resistance between the RF output pin and ground pin and got around ~3-4 Ohm with digital voltage meter. This seems low. Am I missing something?...
Hi,
I have two nRF52833 DKs and both of them has connected to nRF21540 EK. I set the transmitter sending out 244 bytes data without stopping and measure it's current. The...
Hi there,
I want to debugging my beacon project card which designed with NRF52832 MCU
I have NRF54L15 PDK Development Kit and it has debugger on the kit.
How can I debug...
Reporting this here as the project GitHub asked that bugs be reported via DevZone.
The latest Power Profiler v4.2.0 has introduced an annoying issue - when running the Power...
I'm studying the nRF Connect SDK Fundamentals course and working with the NRF54L15 PDK. In Lesson 1, I'm trying to turn on LED0. I can build and flash, but the LED won’t turn...
I am using the s120 soft device v2.2.1 as a center communicating with a peer using a s110 soft device.
The peer is a black box an all I have is the documented protocol.
...
The nRF Kconfig extension ( https://marketplace.visualstudio.com/items?itemName=nordic-semiconductor.nrf-kconfig ) does not recognise some of the Zephyr kconfig extensions...
We are currently developing an ECG sensor patch that will operate over a cellular network, and we are considering using the nRF9151 for its LTE-M/NB-IoT capabilities. Since...
I'm interested in determining the current coverage enhancement behavior of a device, and I'm noticing a discrepancy between the AT+CEINFO and AT%CONEVAL results. Specifically...
as my last post issue nrf desktop in ncs SDK cant work when onnect to cmac os - Nordic Q&A - Nordic DevZone - Nordic DevZone .the ncs desktop cant work in mac os in nrf52840...
We are currently mass producing nrf52833. However, there is a problem with BLE communication. The defective product does not appear in the BLE search list at all. The failure...
Hi,
I'm working with UART with DMA(UARTE) on nRF52840. UART does not have HW flow control, just RX-TX.
I'm confused with DMA part. Is DMA circular or I have to reset it...
I have a nRF5340 using nrf connect v3.7.99-nc1 that is in a peripheral role. I establish a l2cap connection to the peripheral, to request a larger amount of data. That works...
Hi,
Working on a new project, custom board, using an nRF52840. Wrote my own DTS and all that. Program works as intended, but the nRF Connect for VS Code plugin refuses to...
