Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
I am developing a BLE mouse that can connect to 3 devices using nRF52840.
The sample code (peripheral_hids_mouse) allows simultaneous connection to multiple centrals....
Hello Team, We are currently building a circuit using nRF52840 CKAA (WLCSP -94) .We have configured P1.03 & P1.05 GPIO pins as UART_TX & RX . Kindly confirm if this pin or...
Hello, I am currently developing on the nRF54H20DK, which i have previously used v3.2.0-preview1 for. Everything works fine on v3.2.0-preview1. I have tried bumping to v3...
I am using the zephyr\samples\subsys\nvs example. By default the program stores data in internal flash in storage_partition. I would like to create a custom board file for...
I am using the peripheral_uart example. Now, our device tree seems to have crashed. Before the crash, I added the following configurations to prj.conf of the application core...
Hello,
I'm having some issues with the channel sounding on the nRF54L15. I'm using two nRF54L15-dk and two custom bords with the nRF54L15.I'm using SDK v3.0.2 for my software...
I’m trying to debug an existing product by opening its old firmware project on a new PC. The project uses nRF5 SDK for Mesh v2.1.1 , SoftDevice S132 , and nRF52832 .
I installed...
I am currently working in project with nrf54l15dk and 3.0.2 sdk. I'm trying to work with peripherals and I want my project to do the following: -Have 2 PWM outputs that used...
Hi DevZone Community
I'm trying to get a simple Hello World sample to run on an nRF5340DK board with a 2.8" ILI9341 based TFT display that has Arduino headers attached ...
Hello,
Im currently in the process of integrating Memfault OTA on the nRF9151 DK. My project has multiple boards: nRF9151 DK connects with nRF52840 DK via UART for communication...
Hi!
I am using the nRF52832 for a small custom PCB for a wearable device and I would appreciate a review from the experts, before proceeding with manufacturing :)
The...
Hi,
I have a FAT file system that I use with an USB Mass Storage feature. I use the mx25r64 NOR flash (the same as the nrf7002dk evalboard). I am working on ncs 3.0.2. ...
TLDR:
I'm working on getting LE Audio working on a Raspberry Pi CM4 setup and running into some frustrating issues. I've got a u-blox NORA-B126 module (with the nRF5340...
Hi nordic engineer
I have a product use nrf52832. And have two project,project use nrf5 17.0.0 SDK and MDK.
The project A choose chip nrf52832 and S132
The project B...
Hi
The nRF54L15-DK suite tests the accuracy of channel sounding, all ncs versions are v3.1.1. I am using the channel_sounding_ras_initiator and channel_sounding_ras_reflector...
