Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
I added two extra buttons to ble_app_blinky (SDK 17.1.0) - port 1.10 and 0.31 I am running the code on an nRF52840 Dongle. The additional buttons are configured exactly like...
Hi,
I am using the sensor server example available in nrf5 sdk for mesh to build my own application on top of it. And the SOC we are using is nRF52832. I am trying to erase...
I see in the nrfx_uarte.c file the statement NRFX_LOG_INFO("Transfer about to send : %d bytes", length);
How can I set the logging for this file on?
#define NRFX_LOG_MODULE...
Hi,
My apologies if this is the wrong place for this.
I've been using the Power Profiler with the PPK2 and I'm very happy with the product, just have a couple small suggestions...
Hi there! I am facing " <err> download_client: Unexpected HTTP response: 400 bad request" error whenever I am trying to download full modem update from AWS S3 bucket. My environment...
Hi,
I attend the introduction course for the nRF's, and I am at Lession 3. The task is to print 'Hello World' to the device, using Serial Port and COMx. I have made the...
Hello,
As per the requirement of my project I need to add a header file into one of the thingy:53 sample.
Can you please guide how can I add a new header file into it...
Hi ,
I am working on thingy53 and using ncs 1.9.1 I need to enable the BMI270 sensor and need the acceleration and gyroscope data from it. So for that, I primary using the...
Hello,
I am using the provisioner example to provision and configure all my sensor nodes in my project. My use case consists of around 60 sensor nodes. While provisioning...
Hi,
I moved my code on a second windows pc, checkout the code from git,download the same nordic sdk and softdevice version, same SES version but running on my board, the...
Devices: nrf52840 peripheral to nrf52833 central
background: We switched the mode from BLE_GAP_PHY_1MBPS, to BLE_GAP_PHY_CODED. The content of the advertisement data was...
Hello,
I want to use standalone logging for each file (/module)(/driver) of my program, therefore register different logging modules with different log levels each. Registering...
Hi,
I am attempting to configure a nRF52840 (packaged as Seeeduino XIAO Sense) for the popular printer software Klipper.
i have the following processor options and am...
Hello I'm trying to use GPIO pins as UART on the nRF 52 DK rather than the default UART pins. How do I change the pin configuration? I'm using nRF SDK version 17.1. 0
