Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am developing a product using the nRF52840. I am currently running into a difficult problem. I inquired about it 2 years ago, but it has not been resolved.
I need to process...
Hi, on the nRF52820-QDAA I am using pin 5 AIN3 / P0.05 as an GPIO output to drive a LED (active low).
This does not work in the software, when I drive the pin high with...
Hello,
NRF5340, NCS2.0.2, VScode
I designed a headset，MCU is 5340, and a external flash for DSP program.
the external flash connect to DSP and 5340 use SPI;
i can...
Hello,
I was able to build the nRF Desktop sample application on the nRF5340 platform, but when trying to debug, I get the following error:
Here is my build configuration...
Dear ,
I am going to use debug out function on RF5340 DK.
connection is as below: customer board conncet to nRF5340DK.
customer board use nRF52833.
I tried many times...
Hi,
I was just wondering if the nrf52840 Dongle is in some ways inferior to the other development boards in terms of its capabilities?
As I was going through the examples...
Hi,
I am using a nrf528409dk for my application development using nCS. I have various features from which I need to understand how to add some high priority features into...
Hi,
I'm working with the ncs 1.6.1 peripheral_uart example and am looking to increase the size of the data frame to send 240 bytes per data frame.
I have seen several...
I am taking mqqt_simple of NRF9160 as reference for this question,
This is questing regarding, what is recommendation / Philosophy of using MQTT in NRF9160 with other codes...
Hi,
I'm programming a custom board based on Taiyo-Yuden EYSHSNZWZ module (with nRF52832).
I'm using the secure_bootloader example from SDK for OTA DFU, in order to flash...
I'm using the nRF-PPK2 to measure device power usage. I've noticed even at low sampling frequencies (>= 100Hz) it exhibits considerable lag at some point. Most annoyingly...
Hi Sir,
As we know the nRF5340 doesn't release the Circuit Board Guidelines (nAN-40) like nRF52840 yet.
If we need to design the nRF5340, could you share the recommended...
Hello,
I'm doing a comparison between MQTT on TCP and CoAP on UDP over NB-IoT and LTE-M. The communication to the cloud works as expected for both protocols. MQTT is used...
Hi all,
I'm working on a custom Bootloader for my nrf52840-based board, and it needs to support DFU from external SPI Flash. I previously was successful with a "first draft...
