Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
Hello everyone,
I am using NRF5340-DK for my project and I am trying to combine X509 certificates (using MBEDTLS) with RSA operations (using PSA). This is my current proj...
I am working with the wisblock 4631 from rak, that contains an NRF52840. I am working with the Zephyr infrastructure and uploading code via the Nordic extension for VS Code...
Hello,
We have developed a custom System-on-Module based on the nRF9151 SiP and are ready to begin testing its NTN (Non-Terrestrial Network) capabilities.
Following the...
Thingy91I: Is there a sample project accessing the environmental sensor (BME688) ?
If not, perhaps a project to access a device via I2C by the nrf5340 SIP.
A related question...
I am trying to use the HTTPS_Client example but I am struggling to get it working. It returns 200 unmodified, which makes me think everything is working in terms of the board...
Hi, I’m trying to provision a P‑256 key pair into the KMU at runtime on an nRF54L15 (SDK v2.9.1) but psa_generate_key consistently returns PSA_ERROR_NOT_SUPPORTED, even when...
Hi,
In our project, we are planning to use the nRF9160 for both LTE-M and Wi-Fi. Thus, we have connected the nRF9160-DK to the nRF7002-EK in the developing phase as we read...
Hello,
As the LE Audio controller for nRF5340 library is deprecated in favor of the Nordic Semiconductor’s standard Softdevice Controller. We have started to use the Softdevice...
I am using the nrf54l15-dk. I had a look at the datasheet and it shows that a watchdog reset does not reset the GRTC. On my code, I tested that and I see that GRTC resets...
Issue: It appears that whether or not TLS is used by an MQTT client MUST be configured at compile-time. An application with the Kconfig symbols enabled to allow TLS to be...
Hi Nordic S .team,
Could you please help me analyze the following inconsistencies, and also provide the requested documentation?
I’m trying to interpret the AuTerm messages...
Hi Nordic Team,
I am working on matter-based product development using nRF54L15 and looking for machine learning support for the same SoC. Can you please confirm if machine...
Hi
I tried to find this file in the SDK folder and it does not exist. I do have it enabled in the stock sdk_config.h
mike@slavebox armgcc % find /Applications/nRF5_SDK_17...
Dear Nordic team,
i am stilll struggeling with the GPIO set-up in system off mode. It seems, that both GPIO_INT_EDGE_TO_ACTIVE and GPIO_INT_LEVEL_ACTIVE are working fine...
I am getting started with the nrf52840 dk, and I am unable to clear the flash with the Quick start . Here are my logs: 2025-09-24T02:11:29.285Z INFO Initialising the bundled...
