I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
My custom card has ic nrf52832QFAAE0 AND NRF52DK has ic NRF52832QFAAE1.MESH SDK EXAMPLES runs properly on NRF52DK but not working on my hardware with ic NRF52832QFAAE0...
Hi,
What cellular connectivity, the provider's DNS, and backend cloud services, invariably connecting over MQTT is transient and the internal blocking timeout of mqtt_client_tls_connect...
I'm using Zephyr on a nRF52840 and I'd like to use the QSPI with the Fat Filesystem. I added the following Config statements to prj.conf:
The nrfx QSPI driver and file...
Hello,
I am wondering where to change the baud rate for the UART in the NRFConnect SDK using zephyr. I am working with the peripheral_uart example.
Thanks,
RJ
Hello,
i just migrated from nRF51 to nRF52. I tried to implement my custom service. I followed the tutorial from this site: https://github.com/bjornspockeli/custom_ble_service_example...
Hello,
in our application we have two devices. A nrf52840DK as central and a BMD-300-EVAL (contains a nRF52832 chip) as peripheral. We need a timer/counter that generates...
Hi,
I had used nRF Connect Programmer to flash nRF Sniffer firmware on my nRF52840 Dongle, but after that, when I tried to flash the firmware again, I found that there was...
Hi,
I want to add new peer to peer manager using pm_peer_new().
pm_peer_id_t p1 = 0;
pm_peer_new(&p1,&bond_info,NULL);
there are no peers, so trying to add as peer_id...
Bought 2 nRF5340 DK kits from Mouser. Followed the setup instructions and fell at the first hurdle. Attached NF antenna, connected to USB and switched on.
Nothing. Green...
Hello,
I am currently working on a project that requires data to be sent over Bluetooth. I currently have an NRF52832 Development board and have been trying examples and...
Is there any difference in terms of RF performance between different hardware versions of nRF52840? Can someone point me to the relevant documentation?
Thank you
I am working on the nRF52840 DK board SAADC module with nRF5_SDK_17.0.0 SDK, and I am unable to get the output on RTT.\
I am working on the pre-prepared program from the...
Click DFU after connect. Navigate to folder. Click .zip update file. Click OK. File name does NOT appear in chosen text box, box remains empty. Works correctly on English...
Hi everybody, I'm trying to set up my 52840 DK to scan for BLE_GAP_PHY_CODED advertising packets from 52840 Dongle. I think I was able to program the dongle, because it doesn...
